fpga入门串口定时1秒发送1字节

一、程序说明

FPGA通过串口定时发送数据，每秒发送1字节，数据不断自增
参考小梅哥教程

二、 uart_tx.v

`timescale 1ns / 1ps

module uart_tx(
    input		wire 				    sclk,
	input		wire				    rst_n,
	output		reg	                   uart_tx
    );
    
parameter  		CLK_FREQ 	    = 50000000;	//时钟频率50M
parameter  		UART_BAUD 	    = 115200;	//时钟频率50M
parameter  		MAX_BIT_COUNT 	= 9;	//时钟频率50M
localparam 		MAX_BAUD_CNT 	= CLK_FREQ / UART_BAUD;//434

reg [7:0] write_data;   //发送数据

//运行计数器
reg [31:0] run_cnt;	//波特率计数器
always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        run_cnt <= 32'd0;
    else if(run_cnt == CLK_FREQ)
         run_cnt <= 0;
    else
        run_cnt <= run_cnt + 1;
end

//波特率计数器
reg [8:0] baud_cnt;	//波特率计数器
reg en_baud_cnt;	//波特率计数器开关
always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        baud_cnt <= 8'd0;
    else if(en_baud_cnt == 1'b1) begin
        if(baud_cnt == MAX_BAUD_CNT)
            baud_cnt <= 8'd0;
        else
            baud_cnt <= baud_cnt + 1;
    end
    else
        baud_cnt <= baud_cnt;
end

//发送位计数器
reg [4:0] bit_cnt = 0;	//波特率计数器
always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        bit_cnt <= 4'd0;
    else if(baud_cnt == MAX_BAUD_CNT)
        begin
            if(bit_cnt ==  MAX_BIT_COUNT)
                bit_cnt <= 4'd0;
            else
                bit_cnt <= bit_cnt + 1;
        end
    else
        bit_cnt <= bit_cnt;
end 

//位发送逻辑
always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        uart_tx <= 1'b0;
    else if(baud_cnt == MAX_BAUD_CNT/2)
        begin
            if(bit_cnt ==  0)
                uart_tx <= 1'b0;
            else if(bit_cnt == MAX_BIT_COUNT)
                uart_tx <= 1'b1;
            else
            begin
            case(bit_cnt)
                1:uart_tx <= write_data[0];
                2:uart_tx <= write_data[1];
                3:uart_tx <= write_data[2];
                4:uart_tx <= write_data[3];
                5:uart_tx <= write_data[4];
                6:uart_tx <= write_data[5];
                7:uart_tx <= write_data[6];
                8:uart_tx <= write_data[7];
                default:uart_tx <= uart_tx;
            endcase
            end
            //uart_tx <= write_data[bit_cnt-1];
        end
    else
        uart_tx <= uart_tx;
end

always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        en_baud_cnt <= 1'b0;
    else if(run_cnt == 0) begin
        en_baud_cnt <= 1'b1;
    end
    else if(bit_cnt ==  MAX_BIT_COUNT && baud_cnt == MAX_BAUD_CNT)
        en_baud_cnt <= 1'b0;
    else
        en_baud_cnt <= en_baud_cnt;
end

always @(posedge sclk or negedge rst_n)
begin
    if(rst_n == 1'b0)
        write_data <= 8'd0;
    else if(run_cnt == 0)
        write_data <= write_data + 1;
    else
        write_data <= write_data;
end

endmodule