20240703在飞凌OK3588-C开发板上刷Rockchip原厂的Buildroot20220811
2024/7/3 18:25
详细的刷机LOG：
[BEGIN] 2024/7/3 18:18:49
root@RK3588:/# DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gc060f28d70-220414 #zyf (Apr 18 2022 - 18:13:34)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 1
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5ae6932916...) + OK
## Checking uboot 0x00200000 ... sha256(c944ba6cca...) + OK
## Checking fdt 0x00327618 ... sha256(c07f4a4d71...) + OK
## Checking atf-2 0x000f0000 ... sha256(c00c7fd75b...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(4ed9cd20b5...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 114.217 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-384-g45c8fcb44:derrick.huang
NOTICE: BL31: Built : 15:14:04, Jun 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-645-g87d94c5ef8 #xb.wang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #1 Tue Jun 14 10:44:31 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-dirty #viewpro (Jul 03 2024 - 15:52:09 +0800)
Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: edb4f000
Relocation fdt: eb9fa2e8 - eb9fecd0
CR: M/C/I
Using default environment
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: None
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 LP4 V10 Board
download key pressed... entering download mode...
RKUSB: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x733c000
\DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gc060f28d70-220414 #zyf (Apr 18 2022 - 18:13:34)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5ae6932916...) + OK
## Checking uboot 0x00200000 ... sha256(c944ba6cca...) + OK
## Checking fdt 0x00327618 ... sha256(c07f4a4d71...) + OK
## Checking atf-2 0x000f0000 ... sha256(c00c7fd75b...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(4ed9cd20b5...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 114.495 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-384-g45c8fcb44:derrick.huang
NOTICE: BL31: Built : 15:14:04, Jun 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-645-g87d94c5ef8 #xb.wang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #1 Tue Jun 14 10:44:31 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-dirty #viewpro (Jul 03 2024 - 15:52:09 +0800)
Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: edb4f000
Relocation fdt: eb9fa2e8 - eb9fecd0
CR: M/C/I
Using default environment
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: recovery (misc)
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 LP4 V10 Board
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
Using display timing dts
dsi@fde20000: detailed mode clock 132000 kHz, flags[a]
H: 1080 1095 1099 1129
V: 1920 1935 1937 1952
bus_format: 100e
VOP update mode to: 1080x1920p0, type: MIPI0 for VP3
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP3 enable Esmart3[654x270->654x270@213x825] fmt[2] addr[0xedf04000]
final DSI-Link bandwidth: 880000 Kbps x 4
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fde80000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP0 enable Esmart0[654x270->654x270@633x405] fmt[2] addr[0xedf04000]
CEA mode used vic=17
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fdea0000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI1 for VP1
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP1 enable Esmart1[654x270->654x270@633x405] fmt[2] addr[0xedf04000]
CEA mode used vic=17
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 24000 KHz
b1pll 24000 KHz
lpll 24000 KHz
v0pll 24000 KHz
aupll 786431 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 850000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 594000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
Net: eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "recovery"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe76792c0 with size 0x04180000
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e76792c0 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe76a1ec0
Data Size: 31035904 Bytes = 29.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00400000
Entry Point: 0x00400000
Hash algo: sha256
Hash value: 2dd220cbafe2d15ac8d4a335c6b7c0495a58964143acade7d2fbc96a318b2e56
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at e76792c0 ...
Using 'conf' configuration
Trying 'ramdisk' ramdisk subimage
Description: unavailable
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0xe943b0c0
Data Size: 37478527 Bytes = 35.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x0a200000
Entry Point: unavailable
Hash algo: sha256
Hash value: 55b6753389b15b36c7202dfd4bf96f682d627589f6cbfcd27ed15634eecd100a
Verifying Hash Integrity ... sha256+ OK
Loading ramdisk from 0xe943b0c0 to 0x0a200000
## Loading fdt from FIT Image at e76792c0 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe7679ac0
Data Size: 164816 Bytes = 161 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: 1656632d3a95e6697bd165a8eb663c4add2a47eec310e9e5b555fc82cb851c98
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Loading Kernel Image from 0xe76a1ec0 to 0x00400000 ... OK
kernel loaded at 0x00400000, end = 0x02199200
'reserved-memory' cma: addr=10000000 size=8000000
Using Device Tree in place at 000000000a100000, end 000000000a12b3cf
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 1524.23 ms
Starting kernel ...
[ 1.639646] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 1.639668] Linux version 5.10.66 (viewpro@viewpro-ThinkBook-16-G5-IRH) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Wed Jul 3 15:52:23 CST 2024
[ 1.650560] Machine model: Rockchip RK3588 EVB7 LP4 V10 Board
[ 1.650628] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[ 1.654924] printk: bootconsole [uart8250] enabled
[ 1.657871] efi: UEFI not found.
[ 1.663926] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 1.665073] Reserved memory: created CMA memory pool at 0x0000000010000000, size 128 MiB
[ 1.665818] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[ 1.802927] Zone ranges:
[ 1.803173] DMA [mem 0x0000000000200000-0x00000000ffffffff]
[ 1.803748] DMA32 empty
[ 1.804017] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.804590] Movable zone start for each node
[ 1.804984] Early memory node ranges
[ 1.805316] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 1.805894] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 1.806473] node 0: [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.807053] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 1.851801] psci: probing for conduit method from DT.
[ 1.852276] psci: PSCIv1.1 detected in firmware.
[ 1.852703] psci: Using standard PSCI v0.2 function IDs
[ 1.853189] psci: Trusted OS migration not required
[ 1.853641] psci: SMC Calling Convention v1.2
[ 1.854406] percpu: Embedded 30 pages/cpu s83816 r8192 d30872 u122880
[ 1.855195] Detected VIPT I-cache on CPU0
[ 1.855609] CPU features: detected: GIC system register CPU interface
[ 1.856204] CPU features: detected: Virtualization Host Extensions
[ 1.856779] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 1.857425] alternatives: patching kernel code
[ 1.858118] Built 1 zonelists, mobility grouping on. Total pages: 1995336
[ 1.858756] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTUUID=614e0000-0000
[ 1.861944] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 1.863050] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 1.863773] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 1.870308] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[ 1.938249] Memory: 7685732K/8108032K available (15040K kernel code, 3172K rwdata, 5700K rodata, 6272K init, 517K bss, 291228K reserved, 131072K cma-reserved)
[ 1.939689] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 1.940321] ftrace: allocating 56951 entries in 223 pages
[ 2.030668] ftrace: allocated 223 pages with 7 groups
[ 2.031415] rcu: Hierarchical RCU implementation.
[ 2.031854] rcu: RCU event tracing is enabled.
[ 2.032273] Rude variant of Tasks RCU enabled.
[ 2.032691] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 2.038482] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 2.041140] GICv3: GIC: Using split EOI/Deactivate mode
[ 2.041626] GICv3: 480 SPIs implemented
[ 2.041980] GICv3: 0 Extended SPIs implemented
[ 2.042420] GICv3: Distributor has no Range Selector support
[ 2.042947] GICv3: 16 PPIs implemented
[ 2.043335] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[ 2.044083] ITS [mem 0xfe640000-0xfe65ffff]
[ 2.044518] ITS@0x00000000fe640000: allocated 8192 Devices @1001e0000 (indirect, esz 8, psz 64K, shr 0)
[ 2.045403] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1001f0000 (flat, esz 2, psz 64K, shr 0)
[ 2.046359] ITS: using cache flushing for cmd queue
[ 2.046842] ITS [mem 0xfe660000-0xfe67ffff]
[ 2.047271] ITS@0x00000000fe660000: allocated 8192 Devices @100210000 (indirect, esz 8, psz 64K, shr 0)
[ 2.048157] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100220000 (flat, esz 2, psz 64K, shr 0)
[ 2.049112] ITS: using cache flushing for cmd queue
[ 2.049712] GICv3: using LPI property table @0x0000000100230000
[ 2.050373] GIC: using cache flushing for LPI property table
[ 2.050901] GICv3: CPU0: using allocated LPI pending table @0x0000000100240000
[ 2.051728] random: get_random_bytes called from start_kernel+0x3dc/0x5c8 with crng_init=0
[ 2.167406] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 2.168715] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 2.169699] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 2.171503] Console: colour dummy device 80x25
[ 2.171935] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 2.172874] pid_max: default: 32768 minimum: 301
[ 2.173426] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.174134] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.176421] rcu: Hierarchical SRCU implementation.
[ 2.177662] Platform MSI: msi-controller@fe640000 domain created
[ 2.178248] Platform MSI: msi-controller@fe660000 domain created
[ 2.179081] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[ 2.179857] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[ 2.180726] EFI services will not be available.
[ 2.181462] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[ 2.183097] Detected VIPT I-cache on CPU1
[ 2.183132] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[ 2.183149] GICv3: CPU1: using allocated LPI pending table @0x0000000100250000
[ 2.183189] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 2.184456] Detected VIPT I-cache on CPU2
[ 2.184485] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[ 2.184502] GICv3: CPU2: using allocated LPI pending table @0x0000000100260000
[ 2.184542] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 2.185785] Detected VIPT I-cache on CPU3
[ 2.185812] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[ 2.185829] GICv3: CPU3: using allocated LPI pending table @0x0000000100270000
[ 2.185864] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 2.187094] CPU features: detected: Spectre-v4
[ 2.187098] Detected PIPT I-cache on CPU4
[ 2.187112] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[ 2.187121] GICv3: CPU4: using allocated LPI pending table @0x0000000100280000
[ 2.187144] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[ 2.188334] Detected PIPT I-cache on CPU5
[ 2.188349] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[ 2.188359] GICv3: CPU5: using allocated LPI pending table @0x0000000100290000
[ 2.188382] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[ 2.189612] Detected PIPT I-cache on CPU6
[ 2.189626] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[ 2.189635] GICv3: CPU6: using allocated LPI pending table @0x00000001002a0000
[ 2.189658] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[ 2.190834] Detected PIPT I-cache on CPU7
[ 2.190849] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[ 2.190858] GICv3: CPU7: using allocated LPI pending table @0x00000001002b0000
[ 2.190881] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[ 2.190948] smp: Brought up 1 node, 8 CPUs
[ 2.207481] SMP: Total of 8 processors activated.
[ 2.207912] CPU features: detected: Privileged Access Never
[ 2.208421] CPU features: detected: User Access Override
[ 2.208907] CPU features: detected: 32-bit EL0 Support
[ 2.209375] CPU features: detected: Common not Private translations
[ 2.209954] CPU features: detected: RAS Extension Support
[ 2.210447] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 2.211230] CPU features: detected: CRC32 instructions
[ 2.211697] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 2.212333] CPU features: detected: RCpc load-acquire (LDAPR)
[ 2.212935] CPU: All CPU(s) started at EL2
[ 2.214658] devtmpfs: initialized
[ 2.224810] Registered cp15_barrier emulation handler
[ 2.225275] Registered setend emulation handler
[ 2.225755] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 2.226639] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 2.228466] pinctrl core: initialized pinctrl subsystem
[ 2.229193] DMI not present or invalid.
[ 2.229650] NET: Registered protocol family 16
[ 2.230881] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 2.231621] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 2.232919] thermal_sys: Registered thermal governor 'fair_share'
[ 2.232921] thermal_sys: Registered thermal governor 'step_wise'
[ 2.233474] thermal_sys: Registered thermal governor 'user_space'
[ 2.234017] thermal_sys: Registered thermal governor 'power_allocator'
[ 2.234694] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 2.236043] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ 2.236794] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[ 2.237544] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[ 2.238295] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[ 2.239049] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[ 2.239790] cpuidle: using governor menu
[ 2.240154] Registered FIQ tty driver
[ 2.240635] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 2.241359] ASID allocator initialised with 65536 entries
[ 2.243374] printk: console [ramoops-1] enabled
[ 2.243786] pstore: Registered ramoops as persistent store backend
[ 2.244346] ramoops: using 0xf0000@0x110000, ecc: 0
[ 2.286900] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[ 2.287719] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[ 2.288506] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[ 2.289355] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[ 2.290184] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[ 2.290801] rockchip-pinctrl pinctrl: probed pinctrl
[ 2.304610] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 2.305113] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 2.305637] fiq_debugger_probe: could not install nmi irq handler
[ [ 2.306236] printk: console [ttyFIQ0] enabled
2.306236] printk: console [ttyFIQ0] enabled
[ 2.307010] printk: bootconsole [uart8250] disabled
[ 2.307010] printk: bootconsole [uart8250] disabled
[ 2.307538] Registered fiq debugger ttyFIQ0
[ 2.307868] vcc5v0_sys: supplied by vcc12v_dcin
[ 2.307992] vcc5v0_usbdcin: supplied by vcc12v_dcin
[ 2.308106] vcc5v0_usb: supplied by vcc5v0_usbdcin
[ 2.308236] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[ 2.308407] vcc3v3_pcie30: supplied by vcc12v_dcin
[ 2.308542] vcc5v0_host: supplied by vcc5v0_usb
[ 2.309335] iommu: Default domain type: Translated
[ 2.309411] rk_iommu fdab9000.iommu: version = 2
[ 2.309804] rk_iommu fdb50800.iommu: version = 2
[ 2.310038] rk_iommu fdb60f00.iommu: version = 2
[ 2.310213] rk_iommu fdb70f00.iommu: version = 2
[ 2.310366] rk_iommu fdb90480.iommu: version = 2
[ 2.310540] rk_iommu fdba0800.iommu: version = 2
[ 2.310714] rk_iommu fdba4800.iommu: version = 2
[ 2.310886] rk_iommu fdba8800.iommu: version = 2
[ 2.311058] rk_iommu fdbac800.iommu: version = 2
[ 2.311233] rk_iommu fdbb0800.iommu: version = 2
[ 2.311415] rk_iommu fdbdf000.iommu: version = 2
[ 2.311671] rk_iommu fdbef000.iommu: version = 2
[ 2.311939] rk_iommu fdc38700.iommu: version = 2
[ 2.312205] rk_iommu fdc48700.iommu: version = 2
[ 2.312405] rk_iommu fdcb7f00.iommu: version = 2
[ 2.312570] rk_iommu fdce0800.iommu: version = 2
[ 2.312674] rk_iommu fdd97e00.iommu: version = 2
[ 2.312980] SCSI subsystem initialized
[ 2.313056] usbcore: registered new interface driver usbfs
[ 2.313071] usbcore: registered new interface driver hub
[ 2.313087] usbcore: registered new device driver usb
[ 2.313121] mc: Linux media interface: v0.10
[ 2.313133] videodev: Linux video capture interface: v2.00
[ 2.313157] pps_core: LinuxPPS API ver. 1 registered
[ 2.313161] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.313167] PTP clock support registered
[ 2.313420] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 2.313453] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 2.314578] Advanced Linux Sound Architecture Driver Initialized.
[ 2.314758] Bluetooth: Core ver 2.22
[ 2.314772] NET: Registered protocol family 31
[ 2.314775] Bluetooth: HCI device and connection manager initialized
[ 2.314781] Bluetooth: HCI socket layer initialized
[ 2.314786] Bluetooth: L2CAP socket layer initialized
[ 2.314793] Bluetooth: SCO socket layer initialized
[ 2.316070] rockchip-cpuinfo cpuinfo: SoC : 35881000
[ 2.316076] rockchip-cpuinfo cpuinfo: Serial : a75320c211642584
[ 2.316389] clocksource: Switched to clocksource arch_sys_counter
[ 2.607497] NET: Registered protocol family 2
[ 2.607600] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 2.609397] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
[ 2.609486] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 2.609813] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[ 2.610512] TCP: Hash tables configured (established 65536 bind 65536)
[ 2.610563] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 2.610704] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 2.610942] NET: Registered protocol family 1
[ 2.611170] RPC: Registered named UNIX socket transport module.
[ 2.611177] RPC: Registered udp transport module.
[ 2.611181] RPC: Registered tcp transport module.
[ 2.611184] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.611513] PCI: CLS 0 bytes, default 64
[ 2.611763] Trying to unpack rootfs image as initramfs...
[ 3.155923] Freeing initrd memory: 36600K
[ 3.156652] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 3.158603] Initialise system trusted keyrings
[ 3.158662] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 3.160630] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.160875] NFS: Registering the id_resolver key type
[ 3.160884] Key type id_resolver registered
[ 3.160888] Key type id_legacy registered
[ 3.160905] ntfs: driver 2.1.32 [Flags: R/O].
[ 3.160983] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 3.161071] fuse: init (API version 7.32)
[ 3.161196] SGI XFS with security attributes, no debug enabled
[ 3.180394] NET: Registered protocol family 38
[ 3.180402] Key type asymmetric registered
[ 3.180406] Asymmetric key parser 'x509' registered
[ 3.180422] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 3.180426] io scheduler mq-deadline registered
[ 3.180429] io scheduler kyber registered
[ 3.180878] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[ 3.181103] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 3.188486] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[ 3.188662] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[ 3.191097] rk-pcie fe150000.pcie: invalid prsnt-gpios property in node
[ 3.191184] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[ 3.191208] rk-pcie fe170000.pcie: no vpcie3v3 regulator found
[ 3.191330] pwm-backlight backlight: supply power not found, using dummy regulator
[ 3.191371] rk-pcie fe170000.pcie: missing legacy IRQ resource
[ 3.191383] rk-pcie fe170000.pcie: IRQ msi not found
[ 3.191386] rk-pcie fe170000.pcie: use outband MSI support
[ 3.191390] rk-pcie fe170000.pcie: Missing *config* reg space
[ 3.191398] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[ 3.191410] rk-pcie fe170000.pcie: err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[ 3.191418] rk-pcie fe170000.pcie: IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[ 3.191427] rk-pcie fe170000.pcie: MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[ 3.191433] rk-pcie fe170000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[ 3.191456] rk-pcie fe170000.pcie: Missing *config* reg space
[ 3.191481] rk-pcie fe170000.pcie: invalid resource
[ 3.191494] mpp_service mpp-srv: c71d300e428a author: Jianqun Xu 2022-06-22 video: rockchip: mpp: reset buffer members when release buffer
[ 3.191499] mpp_service mpp-srv: probe start
[ 3.192775] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[ 3.192979] mpp_vdpu2 fdb50400.vdpu: probe device
[ 3.193084] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[ 3.193089] vdpu_init:501: No aclk reset resource define
[ 3.193094] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[ 3.193097] vdpu_init:504: No hclk reset resource define
[ 3.193179] mpp_vdpu2 fdb50400.vdpu: probing finish
[ 3.193383] mpp_vepu2 jpege-ccu: probing start
[ 3.193389] mpp_vepu2 jpege-ccu: probing finish
[ 3.193511] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[ 3.193643] mpp_vepu2 fdba0000.jpege-core: probing start
[ 3.193748] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[ 3.193827] mpp_vepu2 fdba0000.jpege-core: probing finish
[ 3.193925] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[ 3.194053] mpp_vepu2 fdba4000.jpege-core: probing start
[ 3.194147] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[ 3.194223] mpp_vepu2 fdba4000.jpege-core: probing finish
[ 3.194321] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[ 3.194458] mpp_vepu2 fdba8000.jpege-core: probing start
[ 3.194555] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[ 3.194636] mpp_vepu2 fdba8000.jpege-core: probing finish
[ 3.194734] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[ 3.194872] mpp_vepu2 fdbac000.jpege-core: probing start
[ 3.194964] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[ 3.195044] mpp_vepu2 fdbac000.jpege-core: probing finish
[ 3.195325] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[ 3.195468] mpp-iep2 fdbb0000.iep: probe device
[ 3.195587] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[ 3.195657] mpp-iep2 fdbb0000.iep: probing finish
[ 3.195864] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[ 3.196072] mpp_jpgdec fdb90000.jpegd: probe device
[ 3.196251] mpp_jpgdec fdb90000.jpegd: probing finish
[ 3.196621] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[ 3.196676] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[ 3.196760] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[ 3.207407] rk-pcie fe150000.pcie: missing legacy IRQ resource
[ 3.207421] rk-pcie fe150000.pcie: IRQ msi not found
[ 3.207425] rk-pcie fe150000.pcie: use outband MSI support
[ 3.207429] rk-pcie fe150000.pcie: Missing *config* reg space
[ 3.207436] rk-pcie fe150000.pcie: host bridge /pcie@fe150000 ranges:
[ 3.207449] rk-pcie fe150000.pcie: err 0x00f0000000..0x00f00fffff -> 0x00f0000000
[ 3.207457] rk-pcie fe150000.pcie: IO 0x00f0100000..0x00f01fffff -> 0x00f0100000
[ 3.207466] rk-pcie fe150000.pcie: MEM 0x00f0200000..0x00f0ffffff -> 0x00f0200000
[ 3.207472] rk-pcie fe150000.pcie: MEM 0x0900000000..0x093fffffff -> 0x0900000000
[ 3.207498] rk-pcie fe150000.pcie: Missing *config* reg space
[ 3.207522] rk-pcie fe150000.pcie: invalid resource
[ 3.207623] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[ 3.207734] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[ 3.207738] rkvdec2_init:697: No niu aclk reset resource define
[ 3.207743] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[ 3.207747] rkvdec2_init:700: No niu hclk reset resource define
[ 3.207805] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[ 3.207809] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[ 3.207945] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000
[ 3.207950] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000
[ 3.207954] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520
[ 3.207958] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[ 3.207962] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[ 3.207992] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[ 3.208060] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[ 3.208287] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[ 3.208392] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[ 3.208396] rkvdec2_init:697: No niu aclk reset resource define
[ 3.208401] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[ 3.208405] rkvdec2_init:700: No niu hclk reset resource define
[ 3.208452] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[ 3.208469] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[ 3.208627] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[ 3.208631] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[ 3.208635] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[ 3.208639] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[ 3.208644] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[ 3.208671] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[ 3.208858] mpp_rkvenc2 rkvenc-ccu: probing start
[ 3.208864] mpp_rkvenc2 rkvenc-ccu: probing finish
[ 3.208977] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[ 3.209153] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[ 3.209169] mpp_rkvenc2 fdbd0000.rkvenc-core: link mode task capacity 8
[ 3.209310] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[ 3.209394] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[ 3.209461] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[ 3.209674] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[ 3.209690] mpp_rkvenc2 fdbe0000.rkvenc-core: link mode task capacity 8
[ 3.209856] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[ 3.209937] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[ 3.210448] mpp_av1dec: Adding child /av1d@fdc70000
[ 3.210665] mpp_av1dec: register device av1d-master
[ 3.210685] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[ 3.210704] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[ 3.210712] mpp_av1dec av1d-master: Adding to iommu group 17
[ 3.210927] mpp_av1dec av1d-master: probing start
[ 3.211128] mpp_av1dec av1d-master: probing finish
[ 3.211162] mpp_service mpp-srv: probe success
[ 3.218687] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 3.218696] dma-pl330 fea10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 3.219525] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 3.219533] dma-pl330 fea30000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 3.220373] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 3.220381] dma-pl330 fed10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 3.220811] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[ 3.220870] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[ 3.220928] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[ 3.220980] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[ 3.221028] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[ 3.221647] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 3.222404] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 3.222839] febc0000.serial: ttyS9 at MMIO 0xfebc0000 (irq = 93, base_baud = 1500000) is a 16550A
[ 3.223977] random: fast init done
[ 3.224073] random: crng init done
[ 3.224706] rockchip-vop2 fdd90000.vop: Adding to iommu group 16
[ 3.233009] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 3.233021] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 3.233035] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 3.233043] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 3.233061] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 3.233067] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 3.233275] [drm] failed to init overlay plane Cluster0-win1
[ 3.233308] [drm] failed to init overlay plane Cluster1-win1
[ 3.233338] [drm] failed to init overlay plane Cluster2-win1
[ 3.233366] [drm] failed to init overlay plane Cluster3-win1
[ 3.243612] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 3.244209] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 3.244383] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 3.244985] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 3.245140] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 3.245177] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[ 3.250830] panel-simple-dsi fde20000.dsi.0: failed to get power regulator: -517
[ 3.253258] brd: module loaded
[ 3.256100] loop: module loaded
[ 3.256268] zram: Added device: zram0
[ 3.256416] lkdtm: No crash points registered, enable through debugfs
[ 3.256510] system_heap: orders[0] = 6
[ 3.256515] system_heap: orders[1] = 4
[ 3.256519] system_heap: orders[2] = 0
[ 3.257486] ahci fe210000.sata: supply ahci not found, using dummy regulator
[ 3.257556] ahci fe210000.sata: supply phy not found, using dummy regulator
[ 3.257668] ahci fe210000.sata: supply target not found, using dummy regulator
[ 3.257733] ahci fe210000.sata: forcing port_map 0x0 -> 0x1
[ 3.257755] ahci fe210000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 3.257763] ahci fe210000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 3.257772] ahci fe210000.sata: port 0 can do FBS, forcing FBSCP
[ 3.258444] scsi host0: ahci
[ 3.258571] ata1: SATA max UDMA/133 mmio [mem 0xfe210000-0xfe210fff] port 0x100 irq 78
[ 3.259663] rockchip-spi feb20000.spi: no high_speed pinctrl state
[ 3.260913] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[ 3.261066] rk806 spi2.0: ON: 0x40 OFF:0x0
[ 3.262882] vdd_gpu_s0: supplied by vcc5v0_sys
[ 3.263962] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[ 3.264571] vdd_log_s0: supplied by vcc5v0_sys
[ 3.265191] vdd_vdenc_s0: supplied by vcc5v0_sys
[ 3.265875] vdd_ddr_s0: supplied by vcc5v0_sys
[ 3.266297] vdd2_ddr_s3: supplied by vcc5v0_sys
[ 3.266950] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[ 3.267510] vcc_3v3_s3: supplied by vcc5v0_sys
[ 3.268051] vddq_ddr_s0: supplied by vcc5v0_sys
[ 3.268672] vcc_1v8_s3: supplied by vcc5v0_sys
[ 3.269290] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[ 3.269962] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[ 3.270525] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 3.271077] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[ 3.271630] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 3.272272] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 3.272965] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 3.273599] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[ 3.274219] vcc_3v3_s0: supplied by vcc5v0_sys
[ 3.274774] vccio_sd_s0: supplied by vcc5v0_sys
[ 3.275340] pldo6_s3: supplied by vcc5v0_sys
[ 3.275857] rk806 spi2.0: no sleep-setting state
[ 3.275863] rk806 spi2.0: no reset-setting pinctrl state
[ 3.275868] rk806 spi2.0: no dvs-setting pinctrl state
[ 3.278207] libphy: Fixed MDIO Bus: probed
[ 3.278904] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[ 3.279050] rk_gmac-dwmac fe1c0000.ethernet: no regulator found
[ 3.279056] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[ 3.279062] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x43).
[ 3.279067] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay.
[ 3.279072] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff
[ 3.279089] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[ 3.279095] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[ 3.279101] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[ 3.279117] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[ 3.279335] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[ 3.279416] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.279423] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5
[ 3.279429] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[ 3.279434] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[ 3.279438] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[ 3.279443] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[ 3.279475] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[ 3.279480] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.279486] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[ 3.279491] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[ 3.279497] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[ 3.397502] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 3.409724] libphy: stmmac: probed
[ 3.409955] mdio_bus stmmac-1: MDIO device at address 1 is missing.
[ 3.410925] usbcore: registered new interface driver rtl8150
[ 3.410949] usbcore: registered new interface driver r8152
[ 3.414168] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 3.423058] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 3.439724] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 3.449723] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 3.466390] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 3.476390] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 3.493057] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 3.503057] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 3.519723] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 3.569548] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.608070] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.608093] ehci-pci: EHCI PCI platform driver
[ 3.608121] ehci-platform: EHCI generic platform driver
[ 3.610557] ehci-platform fc800000.usb: EHCI Host Controller
[ 3.610659] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[ 3.610724] ehci-platform fc800000.usb: irq 19, io mem 0xfc800000
[ 3.623061] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[ 3.623150] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.623157] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.623162] usb usb1: Product: EHCI Host Controller
[ 3.623167] usb usb1: Manufacturer: Linux 5.10.66 ehci_hcd
[ 3.623172] usb usb1: SerialNumber: fc800000.usb
[ 3.623371] hub 1-0:1.0: USB hub found
[ 3.623387] hub 1-0:1.0: 1 port detected
[ 3.625915] ehci-platform fc880000.usb: EHCI Host Controller
[ 3.625984] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[ 3.626037] ehci-platform fc880000.usb: irq 21, io mem 0xfc880000
[ 3.636410] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[ 3.636505] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.636511] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.636516] usb usb2: Product: EHCI Host Controller
[ 3.636521] usb usb2: Manufacturer: Linux 5.10.66 ehci_hcd
[ 3.636526] usb usb2: SerialNumber: fc880000.usb
[ 3.636770] hub 2-0:1.0: USB hub found
[ 3.636786] hub 2-0:1.0: 1 port detected
[ 3.637171] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.637182] ohci-platform: OHCI generic platform driver
[ 3.637341] ohci-platform fc840000.usb: Generic Platform OHCI controller
[ 3.637445] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[ 3.637499] ohci-platform fc840000.usb: irq 20, io mem 0xfc840000
[ 3.697131] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 3.697139] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.697145] usb usb3: Product: Generic Platform OHCI controller
[ 3.697149] usb usb3: Manufacturer: Linux 5.10.66 ohci_hcd
[ 3.697154] usb usb3: SerialNumber: fc840000.usb
[ 3.697382] hub 3-0:1.0: USB hub found
[ 3.697398] hub 3-0:1.0: 1 port detected
[ 3.697657] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[ 3.697750] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[ 3.697794] ohci-platform fc8c0000.usb: irq 22, io mem 0xfc8c0000
[ 3.757131] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 3.757139] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.757145] usb usb4: Product: Generic Platform OHCI controller
[ 3.757149] usb usb4: Manufacturer: Linux 5.10.66 ohci_hcd
[ 3.757154] usb usb4: SerialNumber: fc8c0000.usb
[ 3.757376] hub 4-0:1.0: USB hub found
[ 3.757392] hub 4-0:1.0: 1 port detected
[ 3.757945] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 3.758038] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5
[ 3.758113] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 3.758139] xhci-hcd xhci-hcd.5.auto: irq 138, io mem 0xfcd00000
[ 3.758260] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.758267] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.758271] usb usb5: Product: xHCI Host Controller
[ 3.758276] usb usb5: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.758281] usb usb5: SerialNumber: xhci-hcd.5.auto
[ 3.758510] hub 5-0:1.0: USB hub found
[ 3.758527] hub 5-0:1.0: 1 port detected
[ 3.758659] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 3.758746] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6
[ 3.758756] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[ 3.758784] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.758830] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 3.758836] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.758841] usb usb6: Product: xHCI Host Controller
[ 3.758845] usb usb6: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.758850] usb usb6: SerialNumber: xhci-hcd.5.auto
[ 3.759112] hub 6-0:1.0: USB hub found
[ 3.759127] hub 6-0:1.0: 1 port detected
[ 3.759334] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 3.759343] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.759435] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 7
[ 3.759520] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 3.759543] xhci-hcd xhci-hcd.6.auto: irq 139, io mem 0xfc400000
[ 3.759667] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.759673] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.759678] usb usb7: Product: xHCI Host Controller
[ 3.759683] usb usb7: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.759687] usb usb7: SerialNumber: xhci-hcd.6.auto
[ 3.759915] hub 7-0:1.0: USB hub found
[ 3.759930] hub 7-0:1.0: 1 port detected
[ 3.760056] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.760141] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 8
[ 3.760150] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0 SuperSpeed
[ 3.760177] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.760223] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 3.760229] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.760233] usb usb8: Product: xHCI Host Controller
[ 3.760238] usb usb8: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.760242] usb usb8: SerialNumber: xhci-hcd.6.auto
[ 3.760456] hub 8-0:1.0: USB hub found
[ 3.760471] hub 8-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.760599] usbcore: registered new interface driver cdc_acm
[ 3.760604] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.760708] usbcore: registered new interface driver uas
[ 3.760772] usbcore: registered new interface driver usb-storage
[ 3.760810] usbcore: registered new interface driver usbserial_generic
[ 3.760823] usbserial: USB Serial support registered for generic
[ 3.760842] usbcore: registered new interface driver cp210x
[ 3.760852] usbserial: USB Serial support registered for cp210x
[ 3.760891] usbcore: registered new interface driver ftdi_sio
[ 3.760901] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.761008] usbcore: registered new interface driver keyspan
[ 3.761019] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 3.761029] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 3.761039] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 3.761049] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 3.761071] usbcore: registered new interface driver option
[ 3.761081] usbserial: USB Serial support registered for GSM modem (1-port)
[ 3.761232] usbcore: registered new interface driver oti6858
[ 3.761242] usbserial: USB Serial support registered for oti6858
[ 3.761263] usbcore: registered new interface driver pl2303
[ 3.761273] usbserial: USB Serial support registered for pl2303
[ 3.761300] usbcore: registered new interface driver qcserial
[ 3.761311] usbserial: USB Serial support registered for Qualcomm USB modem
[ 3.761344] usbcore: registered new interface driver sierra
[ 3.761354] usbserial: USB Serial support registered for Sierra USB modem
[ 3.761836] usbcore: registered new interface driver usbtouchscreen
[ 3.762937] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.3.auto/input/input0
[ 3.763240] i2c /dev entries driver
[ 3.766828] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[ 3.775388] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[ 3.784888] vdd_npu_s0: supplied by vcc5v0_sys
[ 3.793296] i2c i2c-4: 1 i2c clients have been registered at 0x68
[ 3.798479] rtc-hym8563 6-0051: rtc information is valid
[ 3.803125] rtc-hym8563 6-0051: registered as rtc0
[ 3.804346] rtc-hym8563 6-0051: hctosys: unable to read the hardware clock
[ 3.808978] ircut cam_ircut: driver version: 00.01.00
[ 3.809117] ircut cam_ircut: failed get pulse-width,use dafult value 100
[ 3.809274] ircut cam_ircut: probe successful!
[ 3.810611] rkcifhw fdce0000.rkcif: Adding to iommu group 15
[ 3.811152] rkcifhw fdce0000.rkcif: No reserved memory region assign to CIF
[ 3.811366] rkcif rkcif-mipi-lvds2: Adding to iommu group 15
[ 3.811405] rkcif rkcif-mipi-lvds2: rkcif driver version: v00.01.0a
[ 3.811532] rkcif rkcif-mipi-lvds2: attach to cif hw node
[ 3.811547] rkcif rkcif-mipi-lvds2: rkcif wait line 0
[ 3.811560] : terminal subdev does not exist
[ 3.811570] : terminal subdev does not exist
[ 3.811580] : terminal subdev does not exist
[ 3.811589] : terminal subdev does not exist
[ 3.811601] : get_remote_sensor: video pad[0] is null
[ 3.811611] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.811622] : get_remote_sensor: video pad[0] is null
[ 3.811631] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.811641] : get_remote_sensor: video pad[0] is null
[ 3.811651] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.811661] : get_remote_sensor: video pad[0] is null
[ 3.811670] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.815704] rkcif rkcif-mipi-lvds2: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 3.815723] rockchip-mipi-csi2: Async registered subdev
[ 3.815745] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds2!
[ 3.817077] rkisp_hw fdcb0000.rkisp: Adding to iommu group 14
[ 3.817321] rkisp_hw fdcb0000.rkisp: is_thunderboot: 0
[ 3.817337] rkisp_hw fdcb0000.rkisp: max input:0x0@0fps
[ 3.817350] rkisp_hw fdcb0000.rkisp: Missing rockchip,grf property
[ 3.817556] rkisp_hw fdcb0000.rkisp: no find phandle sram
[ 3.818430] rkisp rkisp0-vir0: rkisp driver version: v01.09.00
[ 3.818698] rkisp rkisp0-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 3.819873] usbcore: registered new interface driver uvcvideo
[ 3.819880] USB Video Class driver (1.1.1)
[ 3.821071] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[ 3.821585] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[ 3.821916] Bluetooth: HCI UART driver ver 2.3
[ 3.821923] Bluetooth: HCI UART protocol H4 registered
[ 3.821928] Bluetooth: HCI UART protocol ATH3K registered
[ 3.821955] usbcore: registered new interface driver bfusb
[ 3.821985] usbcore: registered new interface driver btusb
[ 3.822329] cpu cpu0: leakage=12
[ 3.823822] cpu cpu0: pvtm=1510
[ 3.823916] cpu cpu0: pvtm-volt-sel=5
[ 3.824422] cpu cpu4: leakage=10
[ 3.830939] cpu cpu4: pvtm=1747
[ 3.834888] cpu cpu4: pvtm-volt-sel=6
[ 3.836138] cpu cpu6: leakage=11
[ 3.842666] cpu cpu6: pvtm=1746
[ 3.846633] cpu cpu6: pvtm-volt-sel=6
[ 3.848221] cpu cpu0: avs=0
[ 3.848890] cpu cpu4: avs=0
[ 3.849544] cpu cpu6: avs=0
[ 3.849783] cpu cpu0: EM: created perf domain
[ 3.849837] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0
[ 3.850429] cpu cpu4: EM: created perf domain
[ 3.850473] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 3.858846] cpu cpu6: EM: created perf domain
[ 3.859316] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 3.874816] sdhci: Secure Digital Host Controller Interface driver
[ 3.874840] sdhci: Copyright(c) Pierre Ossman
[ 3.874848] Synopsys Designware Multimedia Card Interface Driver
[ 3.875900] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.876418] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[ 3.876445] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[ 3.876459] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[ 3.876514] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 79,32 bit host data width,256 deep fifo
[ 3.877340] dwmmc_rockchip fe2c0000.mmc: Failed getting OCR mask: -22
[ 3.877529] dwmmc_rockchip fe2c0000.mmc: could not set regulator OCR (-22)
[ 3.877541] dwmmc_rockchip fe2c0000.mmc: failed to enable vmmc regulator
[ 3.877648] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 3.877673] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 3.877686] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 3.877725] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 80,32 bit host data width,256 deep fifo
[ 3.877843] leds-gpio: probe of leds failed with error -16
[ 3.877996] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 3.878056] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 3.879227] cryptodev: driver 1.12 loaded.
[ 3.879283] hid: raw HID events driver (C) Jiri Kosina
[ 3.879560] usbcore: registered new interface driver usbhid
[ 3.879570] usbhid: USB HID core driver
[ 3.881035] dwmmc_rockchip fe2d0000.mmc: allocated mmc-pwrseq
[ 3.881050] mmc_host mmc1: card is non-removable.
[ 3.889358] optee: probing for conduit method.
[ 3.889397] optee: revision 3.13 (87d94c5e)
[ 3.889782] optee: initialized driver
[ 3.890615] usbcore: registered new interface driver snd-usb-audio
[ 3.892753] ES8323 7-0011: i2c recv Failed
[ 3.896204] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 3.903344] Initializing XFRM netlink socket
[ 3.903725] NET: Registered protocol family 10
[ 3.904709] Segment Routing with IPv6
[ 3.904769] NET: Registered protocol family 17
[ 3.904794] NET: Registered protocol family 15
[ 3.905098] Bluetooth: RFCOMM socket layer initialized
[ 3.905132] Bluetooth: RFCOMM ver 1.11
[ 3.905147] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.905160] Bluetooth: HIDP socket layer initialized
[ 3.905201] [BT_RFKILL]: Enter rfkill_rk_init
[ 3.905210] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 3.905622] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 3.905662] [WLAN_RFKILL]: can't find rockchip,grf property
[ 3.905672] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ 3.905680] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 3.905689] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 3.905751] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 20 flags = 0.
[ 3.905783] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 10, flags = 0.
[ 3.905794] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 3.905803] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 3.905813] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 3.905821] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 3.906791] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 148.
[ 3.906847] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 22.
[ 3.906862] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 21.
[ 3.906876] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 0.
[ 3.906935] [BT_RFKILL]: Request irq for bt wakeup host
[ 3.907049] [BT_RFKILL]: ** disable irq
[ 3.907116] [BT_RFKILL]: bt_default device registered.
[ 3.907183] Key type dns_resolver registered
[ 3.907937] imx415 3-001a: driver version: 00.01.07
[ 3.907950] imx415 3-001a: Get hdr mode failed! no hdr default
[ 3.907972] imx415 3-001a: Failed to get reset-gpios
[ 3.907989] imx415 3-001a: Failed to get power-gpios
[ 3.907997] imx415 3-001a: could not get default pinstate
[ 3.908004] imx415 3-001a: could not get sleep pinstate
[ 3.908038] imx415 3-001a: supply dvdd not found, using dummy regulator
[ 3.908145] imx415 3-001a: supply dovdd not found, using dummy regulator
[ 3.912570] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[ 3.949440] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[ 3.950120] mmcblk0: mmc0:0001 A3A561 57.6 GiB
[ 3.950338] mmcblk0boot0: mmc0:0001 A3A561 partition 1 4.00 MiB
[ 3.950549] mmcblk0boot1: mmc0:0001 A3A561 partition 2 4.00 MiB
[ 3.950730] mmcblk0rpmb: mmc0:0001 A3A561 partition 3 16.0 MiB, chardev (236:0)
[ 3.953544] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 3.979189] imx415 3-001a: Unexpected sensor id(000000), ret(-5)
[ 3.980222] Loading compiled-in X.509 certificates
[ 3.981108] pstore: Using crash dump compression: deflate
[ 3.981502] rga3_core0 fdb60000.rga: Adding to iommu group 2
[ 3.981764] rga: rga3_core0_irq, irq = 34, match scheduler
[ 3.982333] rga: rga3_core0 driver loaded successfully ver:3.0.76831
[ 3.982373] rga: rga3_core0 probe successfully
[ 3.982997] rga3_core1 fdb70000.rga: Adding to iommu group 3
[ 3.983305] rga: rga3_core1_irq, irq = 35, match scheduler
[ 3.983824] rga: rga3_core1 driver loaded successfully ver:3.0.76831
[ 3.983856] rga: rga3_core1 probe successfully
[ 3.984484] rga: rga2_irq, irq = 36, match scheduler
[ 3.984989] rga: rga2 driver loaded successfully ver:3.2.63318
[ 3.985009] rga: rga2 probe successfully
[ 3.985756] rga: Module initialized. v1.2.14
[ 4.005298] mali fb000000.gpu: Kernel DDK version g12p0-01eac0
[ 4.005808] mali fb000000.gpu: leakage=20
[ 4.007172] mali fb000000.gpu: pvtm=922
[ 4.007204] mali fb000000.gpu: pvtm-volt-sel=5
[ 4.007675] mali fb000000.gpu: avs=0
[ 4.008696] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 136; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 4.009689] mali fb000000.gpu: GPU hardware issue table may need updating:
[ 4.009689] r0p0 status 5 is unknown; treating as r0p0 status 0
[ 4.009703] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[ 4.009788] mali fb000000.gpu: No priority control manager is configured
[ 4.009795] mali fb000000.gpu: No memory group manager is configured
[ 4.009811] mali fb000000.gpu: Protected memory allocator not available
[ 4.010908] mali fb000000.gpu: Couldn't find power_model DT node matching 'arm,mali-simple-power-model'
[ 4.010923] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.static-coefficient = 1*[0]
[ 4.011036] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.dynamic-coefficient = 1*[0]
[ 4.011140] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.ts = 4*[0]
[ 4.011246] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.thermal-zone = ''
[ 4.012799] mali fb000000.gpu: Using configured power model mali-lodx-power-model, and fallback mali-simple-power-model
[ 4.012919] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 4.013592] mali fb000000.gpu: Probed as mali0
[ 4.027576] vendor storage:20190527 ret = 0
[ 4.096707] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 4.110226] pcie20_avdd0v85: supplied by vdd_0v85_s0
[ 4.111426] pcie20_avdd1v8: supplied by avcc_1v8_s0
[ 4.112268] pcie30_avdd0v75: supplied by avdd_0v75_s0
[ 4.113042] pcie30_avdd1v8: supplied by avcc_1v8_s0
[ 4.113781] vcc3v3_lcd0_n: supplied by vcc_1v8_s0
[ 4.121882] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 4.121912] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 4.121942] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 4.121957] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 4.121971] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 4.121984] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 4.122780] [drm] failed to init overlay plane Cluster0-win1
[ 4.122966] [drm] failed to init overlay plane Cluster1-win1
[ 4.123204] [drm] failed to init overlay plane Cluster2-win1
[ 4.123380] [drm] failed to init overlay plane Cluster3-win1
[ 4.168811] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 4.171247] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 4.173149] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 4.175533] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 4.177225] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 4.177300] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[ 4.187606] input: adc-keys as /devices/platform/adc-keys/input/input1
[ 4.236475] <<GTP-INF>>[gt1x_ts_probe:537] GTP Driver Version: V1.4<2015/07/10>
[ 4.236481] <<GTP-INF>>[gt1x_ts_probe:538] GTP I2C Address: 0x14
[ 4.236519] <<GTP-ERR>>[gt1x_parse_dt:334] vdd_ana not specified, fallback to power-supply
[ 4.236944] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 4.619743] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 5.119753] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 5.126620] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 5.126637] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 5.126655] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 5.126666] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 5.126675] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 5.126684] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 5.126942] [drm] failed to init overlay plane Cluster0-win1
[ 5.126980] [drm] failed to init overlay plane Cluster1-win1
[ 5.127016] [drm] failed to init overlay plane Cluster2-win1
[ 5.127053] [drm] failed to init overlay plane Cluster3-win1
[ 5.144551] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 5.145989] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 5.147286] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 5.149203] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 5.150597] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 5.150672] rockchip-drm display-subsystem: bound fde20000.dsi (ops 0xffffffc010fbab90)
[ 5.150746] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffffffc010fbafa0)
[ 5.150818] rockchip-drm display-subsystem: bound fde60000.dp (ops 0xffffffc010fbafa0)
[ 5.297201] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.298128] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.298912] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.299547] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.300144] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.300730] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.300788] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 5.301128] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 5.301182] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 5.301358] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 5.301404] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 5.316567] rk3x-i2c fead0000.i2c: timeout, ipd: 0x90, state: 3
[ 5.316603] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 5.316617] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 5.316629] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 5.339960] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 5.351641] rockchip-vop2 fdd90000.vop: [drm:vop2_setup_layer_mixer_for_vp] *ERROR* wait layer cfg done timeout: 0x75643102--0x75641302
[ 5.502813] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.503500] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.503723] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.503942] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.504160] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 5.504175] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 5.533473] dw-dp fde50000.dp: failed to probe DP link: -110
[ 5.542356] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[ 5.863726] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 6.096454] rk-pcie fe170000.pcie: PCIe Link Fail
[ 6.096471] rk-pcie fe170000.pcie: failed to initialize host
[ 6.229717] rk-pcie fe150000.pcie: PCIe Link Fail
[ 6.229722] rk-pcie fe150000.pcie: failed to initialize host
[ 6.363735] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 6.364814] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[ 6.367206] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card1/input2
[ 6.370362] input: rockchip-hdmi1 rockchip-hdmi1 as /devices/platform/hdmi1-sound/sound/card2/input3
[ 6.372736] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1
[ 6.372745] rockchip-csi2-dphy0: No link between dphy and sensor
[ 6.372868] rockchip-csi2-dphy0: No link between dphy and sensor
[ 6.372876] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.372882] rkcif-mipi-lvds2: Async subdev notifier completed
[ 6.372884] rockchip-csi2-dphy0: No link between dphy and sensor
[ 6.372889] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.372891] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 6.372895] rockchip-csi2-dphy0: No link between dphy and sensor
[ 6.372907] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.372909] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 6.373209] RKNPU fdab0000.npu: Adding to iommu group 0
[ 6.373289] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 6.374375] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[ 6.374386] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[ 6.374393] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[ 6.374565] [drm] Initialized rknpu 0.7.2 20220428 for fdab0000.npu on minor 1
[ 6.376113] RKNPU fdab0000.npu: leakage=11
[ 6.382692] RKNPU fdab0000.npu: pvtm=916
[ 6.387900] RKNPU fdab0000.npu: pvtm-volt-sel=5
[ 6.388141] RKNPU fdab0000.npu: avs=0
[ 6.388194] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 6.416929] RKNPU fdab0000.npu: failed to find power_model node
[ 6.416943] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[ 6.416948] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[ 6.418805] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 6.425618] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 6.426347] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 6.427458] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 405; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '15:54:43', on 'Jul 3 2024'.
[ 6.427694] Mali:
[ 6.427695] Mali device driver loaded
[ 6.427705] rkisp rkisp0-vir0: clear unready subdev num: 1
[ 6.427798] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 6.427810] cfg80211: failed to load regulatory.db
[ 6.427850] rkisp0-vir0: Async subdev notifier completed
[ 6.427856] ALSA device list:
[ 6.427861] #0: rockchip,hdmiin
[ 6.427865] #1: rockchip-hdmi0
[ 6.427869] #2: rockchip-hdmi1
[ 6.516575] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 6.516670] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 6.516703] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 6.516728] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 6.583358] mmc_host mmc1: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 7.110276] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 7.609801] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 7.609820] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 7.609826] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 7.609832] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 7.610282] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 7.829795] mmc_host mmc1: Bus speed (slot 0) = 187500Hz (slot req 100000Hz, actual 93750HZ div = 1)
[ 8.369040] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 8.703136] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 8.703153] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 8.703160] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 8.703165] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 8.869047] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 9.796659] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 9.796745] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 9.796775] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 9.796799] <<GTP-ERR>>[gt1x_init:2341] Init failed, use default setting
[ 10.810173] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 10.810261] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 10.810292] <<GTP-ERR>>[gt1x_get_chip_type:891] I2c communication error.
[ 10.810318] <<GTP-ERR>>[gt1x_init:2351] Get chip type failed!
[ 11.823432] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 11.823518] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 11.823549] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 12.943321] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 12.943407] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 12.943437] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 14.063321] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 14.063408] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 14.063439] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 14.169979] <<GTP-INF>>[gt1x_read_version:859] IC VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID)
[ 14.170056] <<GTP-INF>>[gt1x_init_panel:604] Config group0 used, length:239
[ 14.170089] <<GTP-INF>>[gt1x_init_panel:655] X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1
[ 15.050604] dw-dp fde50000.dp: failed to probe DP link: -110
[ 15.183323] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 15.183411] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 15.500413] dw-dp fde50000.dp: failed to probe DP link: -110
[ 16.196649] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 16.196738] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 17.210037] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 17.210126] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 18.223320] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 18.223405] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 19.236697] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 19.236786] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 19.236816] <<GTP-ERR>>[gt1x_send_cfg:549] Send config failed!
[ 19.236841] <<GTP-ERR>>[gt1x_init:2363] Init panel failed.
[ 19.237337] <<GTP-ERR>>[gt1x_ts_probe:564] GTP init failed!!!
[ 19.237505] Goodix-TS-GT1X: probe of 5-0014 failed with error -2147483644
[ 19.241593] Freeing unused kernel memory: 6272K
[ 19.253283] Run /init as init process
[ 19.273964] /dev/sda1: Can't open blockdev
[ 19.275545] /dev/sda1: Can't open blockdev
mount: mounting /dev/sda1 on /mnt/udisk failed: No such file or directory
[ 19.277089] /dev/mmcblk1p1: Can't open blockdev
[ 19.278505] /dev/mmcblk1p1: Can't open blockdev
mount: mounting /dev/mmcblk1p1 on /mnt/sdcard failed: No such file or directory
mount: mounting PARTLABEL=oem on /oem failed: No such file or directory
mount: mounting PARTLABEL=userdata on /userdata failed: No such file or directory
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: [ 19.335781] udevd[312]: starting version 3.2.10
[ 19.341092] udevd[313]: starting eudev-3.2.10
[ 19.440017] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.440069] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 19.440072] rkcif_scale_ch1: update sensor info failed -19
[ 19.440457] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.440465] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.440485] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 19.440490] rkcif_scale_ch0: update sensor info failed -19
[ 19.440497] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 19.440502] stream_cif_mipi_id1: update sensor info failed -19
[ 19.441346] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.441366] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 19.441369] stream_cif_mipi_id2: update sensor info failed -19
[ 19.441852] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.441870] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 19.441873] stream_cif_mipi_id3: update sensor info failed -19
[ 19.442088] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.442094] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.442112] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 19.442120] rkcif_tools_id0: update sensor info failed -19
[ 19.442121] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 19.442124] stream_cif_mipi_id0: update sensor info failed -19
[ 19.443968] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.444004] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 19.444007] rkcif_tools_id2: update sensor info failed -19
[ 19.445252] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.445289] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 19.445293] rkcif_scale_ch3: update sensor info failed -19
[ 19.450871] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.450906] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 19.450908] rkcif_scale_ch2: update sensor info failed -19
[ 19.454326] rockchip-csi2-dphy0: No link between dphy and sensor
[ 19.454408] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 19.454417] rkcif_tools_id1: update sensor info failed -19
done
Saving random seed: OK
Starting network: OK
Debug: configfs_init
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac1.gs0': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac2.gs0': No such file or directory
[ 19.572620] file system registered
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/rndis.gs0': No such file or directory
[ 19.585964] Mass Storage Function, version: 2009/09/11
[ 19.585992] LUN: removable file: (no medium)
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/hid.usb0': No such file or directory
[ 19.624052] read descriptors
[ 19.624083] read strings
[ 19.760484] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.761181] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.761779] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.762431] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.763033] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.763487] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.763532] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.797350] dw-dp fde50000.dp: failed to probe DP link: -110
[ 19.969818] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.970747] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.971405] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.972007] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.972594] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.972653] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.004437] dw-dp fde50000.dp: failed to probe DP link: -110
[ 20.175768] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.176750] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.177198] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.177607] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.177996] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.178384] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.178408] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.353522] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[ 20.372256] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.372406] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.372738] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.372863] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.372956] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.372970] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.373303] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
[ 20.439204] dw-dp fde50000.dp: failed to probe DP link: -110
[ 20.457163] Freeing drm_logo memory: 732K
Starting input-event-daemon: input-event-daemon: Start parsing /etc/input-event-daemon.conf...
input-event-daemon: Adding device: /dev/input/event0...
input-event-daemon: Adding device: /dev/input/event1...
input-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Adding device: /dev/input/event3...
input-event-daemon: Start listening on 4 devices...
done
sh: groups: command not found
root@RK3588:/# [ 20.856749] dwc3 fc000000.usb: device reset
[ 20.918729] android_work: sent uevent USB_STATE=CONNECTED
[ 20.923702] android_work: sent uevent USB_STATE=CONFIGURED
[ 24.707199] dw-dp fde50000.dp: failed to probe DP link: -110
[ 25.156333] dw-dp fde50000.dp: failed to probe DP link: -110
[ 27.210589] dw-dp fde50000.dp: failed to probe DP link: -110
[ 27.663534] dw-dp fde50000.dp: failed to probe DP link: -110
[ 29.747494] dw-dp fde50000.dp: failed to probe DP link: -110
[ 30.197992] dw-dp fde50000.dp: failed to probe DP link: -110
[ 32.268172] dw-dp fde50000.dp: failed to probe DP link: -110
[ 32.721077] dw-dp fde50000.dp: failed to probe DP link: -110
[ 34.791571] dw-dp fde50000.dp: failed to probe DP link: -110
[ 35.244664] dw-dp fde50000.dp: failed to probe DP link: -110
[ 37.307121] dw-dp fde50000.dp: failed to probe DP link: -110
[ 37.636580] vcc3v3_pcie30: disabling
[ 37.636623] vcc_mipicsi0: disabling
[ 37.636636] vcc_mipicsi1: disabling
[ 37.636646] vcc_mipidphy0: disabling
[ 37.636656] vcc_3v3_sd_s0: disabling
[ 37.760899] dw-dp fde50000.dp: failed to probe DP link: -110
[ 39.840556] dw-dp fde50000.dp: failed to probe DP link: -110
[ 40.291599] dw-dp fde50000.dp: failed to probe DP link: -110
[ 42.357856] dw-dp fde50000.dp: failed to probe DP link: -110
[ 42.807184] dw-dp fde50000.dp: failed to probe DP link: -110
[ 45.267707] dw-dp fde50000.dp: failed to probe DP link: -110
[ 45.717619] dw-dp fde50000.dp: failed to probe DP link: -110
[ 48.184272] dw-dp fde50000.dp: failed to probe DP link: -110
[ 48.634964] dw-dp fde50000.dp: failed to probe DP link: -110
[ 50.157728] EXT4-fs (mmcblk0p8): mounting ext2 file system using the ext4 subsystem
[ 50.172420] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts:
[ 51.104852] dw-dp fde50000.dp: failed to probe DP link: -110
[ 51.276487] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp3
[ 51.316564] rk860-regulator 1-0042: rk860..... reset
[ 51.318008] rk860-regulator 1-0042: force rk860x_reset ok!
[ 51.318505] rk860-regulator 0-0043: rk860..... reset
[ 51.319882] rk860-regulator 0-0043: force rk860x_reset ok!
[ 51.320373] rk860-regulator 0-0042: rk860..... reset
[ 51.321806] rk860-regulator 0-0042: force rk860x_reset ok!
[ 51.354381] xhci-hcd xhci-hcd.6.auto: Host halt failed, -110
[ 51.355006] mpp_av1dec av1d-master: shutdown device
[ 51.355433] mpp_av1dec av1d-master: shutdown success
[ 51.355947] [WLAN_RFKILL]: Enter rfkill_wlan_shutdown
[ 51.356398] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 51.356813] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 51.357324] wifi power off
[ 51.463112] [WLAN_RFKILL]: wifi shut off power [GPIO20-0]
[ 51.463591] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 0
[ 51.464150] xhci-hcd xhci-hcd.6.auto: remove, state 4
[ 51.464603] usb usb8: USB disconnect, device number 1
[ 51.465303] xhci-hcd xhci-hcd.6.auto: USB bus 8 deregistered
[ 51.465865] xhci-hcd xhci-hcd.6.auto: remove, state 4
[ 51.466314] usb usb7: USB disconnect, device number 1
[ 51.499126] xhci-hcd xhci-hcd.6.auto: Host halt failed, -110
[ 51.499626] xhci-hcd xhci-hcd.6.auto: Host controller not halted, aborting reset.
[ 51.500382] xhci-hcd xhci-hcd.6.auto: USB bus 7 deregistered
[ 51.501472] rkisp_hw fdcb0000.rkisp: rkisp_hw_shutdown
[ 51.501959] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown device
[ 51.502461] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown success
[ 51.502986] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown device
[ 51.503506] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown success
[ 51.504032] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown device
[ 51.504537] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown success
[ 51.505057] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown device
[ 51.505562] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown success
[ 51.506082] mpp-iep2 fdbb0000.iep: shutdown device
[ 51.506509] mpp-iep2 fdbb0000.iep: shutdown success
[ 51.506945] mpp_vepu2 fdbac000.jpege-core: shutdown device
[ 51.507430] mpp_vepu2 fdbac000.jpege-core: shutdown success
[ 51.507924] mpp_vepu2 fdba8000.jpege-core: shutdown device
[ 51.508410] mpp_vepu2 fdba8000.jpege-core: shutdown success
[ 51.508910] mpp_vepu2 fdba4000.jpege-core: shutdown device
[ 51.509393] mpp_vepu2 fdba4000.jpege-core: shutdown success
[ 51.509899] mpp_vepu2 fdba0000.jpege-core: shutdown device
[ 51.510381] mpp_vepu2 fdba0000.jpege-core: shutdown success
[ 51.510873] mpp_jpgdec fdb90000.jpegd: shutdown device
[ 51.511324] mpp_jpgdec fdb90000.jpegd: shutdown success
[ 51.511808] mpp_vdpu2 fdb50400.vdpu: shutdown device
[ 51.512247] mpp_vdpu2 fdb50400.vdpu: shutdown success
[ 51.512793] xhci-hcd xhci-hcd.5.auto: remove, state 4
[ 51.513242] usb usb6: USB disconnect, device number 1
[ 51.514075] xhci-hcd xhci-hcd.5.auto: USB bus 6 deregistered
[ 51.514800] xhci-hcd xhci-hcd.5.auto: remove, state 4
[ 51.515258] usb usb5: USB disconnect, device number 1
[ 51.516085] xhci-hcd xhci-hcd.5.auto: USB bus 5 deregistered
[ 51.517094] android_work: sent uevent USB_STATE=DISCONNECTED
[ 51.518453] reboot: Restarting system
DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gc060f28d70-220414 #zyf (Apr 18 2022 - 18:13:34)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 1
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5ae6932916...) + OK
## Checking uboot 0x00200000 ... sha256(c944ba6cca...) + OK
## Checking fdt 0x00327618 ... sha256(c07f4a4d71...) + OK
## Checking atf-2 0x000f0000 ... sha256(c00c7fd75b...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(4ed9cd20b5...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 114.93 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-384-g45c8fcb44:derrick.huang
NOTICE: BL31: Built : 15:14:04, Jun 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-645-g87d94c5ef8 #xb.wang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #1 Tue Jun 14 10:44:31 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-dirty #viewpro (Jul 03 2024 - 15:52:09 +0800)
Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: edb4f000
Relocation fdt: eb9fa2e8 - eb9fecd0
CR: M/C/I
Using default environment
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: normal
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 LP4 V10 Board
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
Using display timing dts
dsi@fde20000: detailed mode clock 132000 kHz, flags[a]
H: 1080 1095 1099 1129
V: 1920 1935 1937 1952
bus_format: 100e
VOP update mode to: 1080x1920p0, type: MIPI0 for VP3
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP3 enable Esmart3[654x270->654x270@213x825] fmt[2] addr[0xedf04000]
final DSI-Link bandwidth: 880000 Kbps x 4
Monitor has basic audio support
can't find to match
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fde80000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP0 enable Esmart0[654x270->654x270@633x405] fmt[2] addr[0xedf04000]
CEA mode used vic=17
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fdea0000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI1 for VP1
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: Failed to get hdmi0_phy_pll ret=-22
rockchip_vop2_init: Failed to get hdmi1_phy_pll ret=-22
warn: can't get assigned-clock-parents's node
VOP VP1 enable Esmart1[654x270->654x270@633x405] fmt[2] addr[0xedf04000]
CEA mode used vic=17
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 24000 KHz
b1pll 24000 KHz
lpll 24000 KHz
v0pll 24000 KHz
aupll 786431 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 850000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 594000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
Net: eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe9a374c0 with size 0x01dc1e00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e9a374c0 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe9a600c0
Data Size: 31035904 Bytes = 29.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00400000
Entry Point: 0x00400000
Hash algo: sha256
Hash value: 2dd220cbafe2d15ac8d4a335c6b7c0495a58964143acade7d2fbc96a318b2e56
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e9a374c0 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe9a37cc0
Data Size: 164816 Bytes = 161 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: 1656632d3a95e6697bd165a8eb663c4add2a47eec310e9e5b555fc82cb851c98
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Loading Kernel Image from 0xe9a600c0 to 0x00400000 ... OK
kernel loaded at 0x00400000, end = 0x02199200
'reserved-memory' cma: addr=10000000 size=8000000
Using Device Tree in place at 000000000a100000, end 000000000a12b3cf
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 1423.601 ms
Starting kernel ...
[ 1.539826] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 1.539847] Linux version 5.10.66 (viewpro@viewpro-ThinkBook-16-G5-IRH) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Wed Jul 3 15:52:23 CST 2024
[ 1.550736] Machine model: Rockchip RK3588 EVB7 LP4 V10 Board
[ 1.550805] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[ 1.555104] printk: bootconsole [uart8250] enabled
[ 1.558050] efi: UEFI not found.
[ 1.564104] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 1.565251] Reserved memory: created CMA memory pool at 0x0000000010000000, size 128 MiB
[ 1.565995] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[ 1.703055] Zone ranges:
[ 1.703302] DMA [mem 0x0000000000200000-0x00000000ffffffff]
[ 1.703877] DMA32 empty
[ 1.704146] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.704719] Movable zone start for each node
[ 1.705113] Early memory node ranges
[ 1.705445] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 1.706023] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 1.706602] node 0: [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.707182] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 1.751955] psci: probing for conduit method from DT.
[ 1.752429] psci: PSCIv1.1 detected in firmware.
[ 1.752856] psci: Using standard PSCI v0.2 function IDs
[ 1.753340] psci: Trusted OS migration not required
[ 1.753791] psci: SMC Calling Convention v1.2
[ 1.754557] percpu: Embedded 30 pages/cpu s83816 r8192 d30872 u122880
[ 1.755348] Detected VIPT I-cache on CPU0
[ 1.755760] CPU features: detected: GIC system register CPU interface
[ 1.756354] CPU features: detected: Virtualization Host Extensions
[ 1.756929] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 1.757576] alternatives: patching kernel code
[ 1.758267] Built 1 zonelists, mobility grouping on. Total pages: 1995336
[ 1.758905] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTUUID=614e0000-0000
[ 1.762093] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 1.763200] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 1.763923] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 1.770464] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[ 1.837765] Memory: 7722340K/8108032K available (15040K kernel code, 3172K rwdata, 5700K rodata, 6272K init, 517K bss, 254620K reserved, 131072K cma-reserved)
[ 1.839203] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 1.839837] ftrace: allocating 56951 entries in 223 pages
[ 1.930294] ftrace: allocated 223 pages with 7 groups
[ 1.931039] rcu: Hierarchical RCU implementation.
[ 1.931477] rcu: RCU event tracing is enabled.
[ 1.931896] Rude variant of Tasks RCU enabled.
[ 1.932315] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 1.938096] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 1.940760] GICv3: GIC: Using split EOI/Deactivate mode
[ 1.941245] GICv3: 480 SPIs implemented
[ 1.941600] GICv3: 0 Extended SPIs implemented
[ 1.942040] GICv3: Distributor has no Range Selector support
[ 1.942567] GICv3: 16 PPIs implemented
[ 1.942954] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[ 1.943700] ITS [mem 0xfe640000-0xfe65ffff]
[ 1.944134] ITS@0x00000000fe640000: allocated 8192 Devices @1001e0000 (indirect, esz 8, psz 64K, shr 0)
[ 1.945020] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1001f0000 (flat, esz 2, psz 64K, shr 0)
[ 1.945977] ITS: using cache flushing for cmd queue
[ 1.946460] ITS [mem 0xfe660000-0xfe67ffff]
[ 1.946889] ITS@0x00000000fe660000: allocated 8192 Devices @100210000 (indirect, esz 8, psz 64K, shr 0)
[ 1.947773] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100220000 (flat, esz 2, psz 64K, shr 0)
[ 1.948729] ITS: using cache flushing for cmd queue
[ 1.949324] GICv3: using LPI property table @0x0000000100230000
[ 1.949984] GIC: using cache flushing for LPI property table
[ 1.950512] GICv3: CPU0: using allocated LPI pending table @0x0000000100240000
[ 1.951341] random: get_random_bytes called from start_kernel+0x3dc/0x5c8 with crng_init=0
[ 2.067037] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 2.068346] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 2.069331] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 2.071139] Console: colour dummy device 80x25
[ 2.071571] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 2.072510] pid_max: default: 32768 minimum: 301
[ 2.073061] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.073769] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.076055] rcu: Hierarchical SRCU implementation.
[ 2.077296] Platform MSI: msi-controller@fe640000 domain created
[ 2.077883] Platform MSI: msi-controller@fe660000 domain created
[ 2.078714] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[ 2.079490] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[ 2.080363] EFI services will not be available.
[ 2.081098] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[ 2.082734] Detected VIPT I-cache on CPU1
[ 2.082771] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[ 2.082788] GICv3: CPU1: using allocated LPI pending table @0x0000000100250000
[ 2.082831] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 2.084093] Detected VIPT I-cache on CPU2
[ 2.084122] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[ 2.084139] GICv3: CPU2: using allocated LPI pending table @0x0000000100260000
[ 2.084178] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 2.085418] Detected VIPT I-cache on CPU3
[ 2.085444] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[ 2.085461] GICv3: CPU3: using allocated LPI pending table @0x0000000100270000
[ 2.085497] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 2.086728] CPU features: detected: Spectre-v4
[ 2.086732] Detected PIPT I-cache on CPU4
[ 2.086746] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[ 2.086755] GICv3: CPU4: using allocated LPI pending table @0x0000000100280000
[ 2.086778] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[ 2.087969] Detected PIPT I-cache on CPU5
[ 2.087985] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[ 2.087994] GICv3: CPU5: using allocated LPI pending table @0x0000000100290000
[ 2.088018] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[ 2.089247] Detected PIPT I-cache on CPU6
[ 2.089262] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[ 2.089271] GICv3: CPU6: using allocated LPI pending table @0x00000001002a0000
[ 2.089294] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[ 2.090471] Detected PIPT I-cache on CPU7
[ 2.090485] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[ 2.090495] GICv3: CPU7: using allocated LPI pending table @0x00000001002b0000
[ 2.090517] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[ 2.090583] smp: Brought up 1 node, 8 CPUs
[ 2.107119] SMP: Total of 8 processors activated.
[ 2.107549] CPU features: detected: Privileged Access Never
[ 2.108057] CPU features: detected: User Access Override
[ 2.108542] CPU features: detected: 32-bit EL0 Support
[ 2.109011] CPU features: detected: Common not Private translations
[ 2.109590] CPU features: detected: RAS Extension Support
[ 2.110083] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 2.110866] CPU features: detected: CRC32 instructions
[ 2.111334] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 2.111969] CPU features: detected: RCpc load-acquire (LDAPR)
[ 2.112572] CPU: All CPU(s) started at EL2
[ 2.114296] devtmpfs: initialized
[ 2.124440] Registered cp15_barrier emulation handler
[ 2.124905] Registered setend emulation handler
[ 2.125391] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 2.126278] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 2.128103] pinctrl core: initialized pinctrl subsystem
[ 2.128828] DMI not present or invalid.
[ 2.129286] NET: Registered protocol family 16
[ 2.130526] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 2.131256] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 2.132538] thermal_sys: Registered thermal governor 'fair_share'
[ 2.132541] thermal_sys: Registered thermal governor 'step_wise'
[ 2.133094] thermal_sys: Registered thermal governor 'user_space'
[ 2.133643] thermal_sys: Registered thermal governor 'power_allocator'
[ 2.134323] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 2.135665] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ 2.136417] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[ 2.137171] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[ 2.137922] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[ 2.138679] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[ 2.139419] cpuidle: using governor menu
[ 2.139780] Registered FIQ tty driver
[ 2.140261] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 2.140987] ASID allocator initialised with 65536 entries
[ 2.143147] printk: console [ramoops-1] enabled
[ 2.143559] pstore: Registered ramoops as persistent store backend
[ 2.144129] ramoops: using 0xf0000@0x110000, ecc: 0
[ 2.186622] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[ 2.187446] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[ 2.188243] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[ 2.189077] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[ 2.189898] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[ 2.190515] rockchip-pinctrl pinctrl: probed pinctrl
[ 2.204313] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 2.204823] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 2.205345] fiq_debugger_probe: could not install nmi irq handler
[ [ 2.205940] printk: console [ttyFIQ0] enabled
2.205940] printk: console [ttyFIQ0] enabled
[ 2.206714] printk: bootconsole [uart8250] disabled
[ 2.206714] printk: bootconsole [uart8250] disabled
[ 2.207242] Registered fiq debugger ttyFIQ0
[ 2.207545] vcc5v0_sys: supplied by vcc12v_dcin
[ 2.207672] vcc5v0_usbdcin: supplied by vcc12v_dcin
[ 2.207791] vcc5v0_usb: supplied by vcc5v0_usbdcin
[ 2.207912] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[ 2.208084] vcc3v3_pcie30: supplied by vcc12v_dcin
[ 2.208234] vcc5v0_host: supplied by vcc5v0_usb
[ 2.208999] iommu: Default domain type: Translated
[ 2.209075] rk_iommu fdab9000.iommu: version = 2
[ 2.209447] rk_iommu fdb50800.iommu: version = 2
[ 2.209676] rk_iommu fdb60f00.iommu: version = 2
[ 2.209850] rk_iommu fdb70f00.iommu: version = 2
[ 2.210008] rk_iommu fdb90480.iommu: version = 2
[ 2.210183] rk_iommu fdba0800.iommu: version = 2
[ 2.210354] rk_iommu fdba4800.iommu: version = 2
[ 2.210528] rk_iommu fdba8800.iommu: version = 2
[ 2.210701] rk_iommu fdbac800.iommu: version = 2
[ 2.210873] rk_iommu fdbb0800.iommu: version = 2
[ 2.211055] rk_iommu fdbdf000.iommu: version = 2
[ 2.211309] rk_iommu fdbef000.iommu: version = 2
[ 2.211587] rk_iommu fdc38700.iommu: version = 2
[ 2.211858] rk_iommu fdc48700.iommu: version = 2
[ 2.212062] rk_iommu fdcb7f00.iommu: version = 2
[ 2.212223] rk_iommu fdce0800.iommu: version = 2
[ 2.212330] rk_iommu fdd97e00.iommu: version = 2
[ 2.212631] SCSI subsystem initialized
[ 2.212704] usbcore: registered new interface driver usbfs
[ 2.212721] usbcore: registered new interface driver hub
[ 2.212736] usbcore: registered new device driver usb
[ 2.212769] mc: Linux media interface: v0.10
[ 2.212780] videodev: Linux video capture interface: v2.00
[ 2.212811] pps_core: LinuxPPS API ver. 1 registered
[ 2.212815] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.212821] PTP clock support registered
[ 2.213066] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 2.213099] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 2.214214] Advanced Linux Sound Architecture Driver Initialized.
[ 2.214392] Bluetooth: Core ver 2.22
[ 2.214405] NET: Registered protocol family 31
[ 2.214409] Bluetooth: HCI device and connection manager initialized
[ 2.214415] Bluetooth: HCI socket layer initialized
[ 2.214419] Bluetooth: L2CAP socket layer initialized
[ 2.214426] Bluetooth: SCO socket layer initialized
[ 2.215700] rockchip-cpuinfo cpuinfo: SoC : 35881000
[ 2.215706] rockchip-cpuinfo cpuinfo: Serial : a75320c211642584
[ 2.216018] clocksource: Switched to clocksource arch_sys_counter
[ 2.507745] NET: Registered protocol family 2
[ 2.507856] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 2.509662] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
[ 2.509751] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 2.510068] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[ 2.510762] TCP: Hash tables configured (established 65536 bind 65536)
[ 2.510812] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 2.510953] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 2.511187] NET: Registered protocol family 1
[ 2.511420] RPC: Registered named UNIX socket transport module.
[ 2.511426] RPC: Registered udp transport module.
[ 2.511430] RPC: Registered tcp transport module.
[ 2.511433] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.511824] PCI: CLS 0 bytes, default 64
[ 2.512777] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 2.514713] Initialise system trusted keyrings
[ 2.514768] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 2.516732] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.516971] NFS: Registering the id_resolver key type
[ 2.516980] Key type id_resolver registered
[ 2.516984] Key type id_legacy registered
[ 2.516999] ntfs: driver 2.1.32 [Flags: R/O].
[ 2.517077] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 2.517161] fuse: init (API version 7.32)
[ 2.517289] SGI XFS with security attributes, no debug enabled
[ 2.536887] NET: Registered protocol family 38
[ 2.536895] Key type asymmetric registered
[ 2.536899] Asymmetric key parser 'x509' registered
[ 2.536914] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 2.536918] io scheduler mq-deadline registered
[ 2.536921] io scheduler kyber registered
[ 2.537356] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[ 2.537573] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 2.544942] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[ 2.545109] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[ 2.547623] rk-pcie fe150000.pcie: invalid prsnt-gpios property in node
[ 2.547626] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[ 2.547667] rk-pcie fe170000.pcie: no vpcie3v3 regulator found
[ 2.547817] pwm-backlight backlight: supply power not found, using dummy regulator
[ 2.547825] rk-pcie fe170000.pcie: missing legacy IRQ resource
[ 2.547836] rk-pcie fe170000.pcie: IRQ msi not found
[ 2.547840] rk-pcie fe170000.pcie: use outband MSI support
[ 2.547845] rk-pcie fe170000.pcie: Missing *config* reg space
[ 2.547852] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[ 2.547865] rk-pcie fe170000.pcie: err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[ 2.547874] rk-pcie fe170000.pcie: IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[ 2.547883] rk-pcie fe170000.pcie: MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[ 2.547890] rk-pcie fe170000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[ 2.547913] rk-pcie fe170000.pcie: Missing *config* reg space
[ 2.547937] rk-pcie fe170000.pcie: invalid resource
[ 2.547980] mpp_service mpp-srv: c71d300e428a author: Jianqun Xu 2022-06-22 video: rockchip: mpp: reset buffer members when release buffer
[ 2.547986] mpp_service mpp-srv: probe start
[ 2.549257] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[ 2.549471] mpp_vdpu2 fdb50400.vdpu: probe device
[ 2.549564] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[ 2.549569] vdpu_init:501: No aclk reset resource define
[ 2.549574] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[ 2.549577] vdpu_init:504: No hclk reset resource define
[ 2.549655] mpp_vdpu2 fdb50400.vdpu: probing finish
[ 2.549858] mpp_vepu2 jpege-ccu: probing start
[ 2.549863] mpp_vepu2 jpege-ccu: probing finish
[ 2.549986] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[ 2.550122] mpp_vepu2 fdba0000.jpege-core: probing start
[ 2.550222] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[ 2.550292] mpp_vepu2 fdba0000.jpege-core: probing finish
[ 2.550388] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[ 2.550519] mpp_vepu2 fdba4000.jpege-core: probing start
[ 2.550615] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[ 2.550693] mpp_vepu2 fdba4000.jpege-core: probing finish
[ 2.550791] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[ 2.550925] mpp_vepu2 fdba8000.jpege-core: probing start
[ 2.551017] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[ 2.551098] mpp_vepu2 fdba8000.jpege-core: probing finish
[ 2.551196] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[ 2.551334] mpp_vepu2 fdbac000.jpege-core: probing start
[ 2.551427] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[ 2.551506] mpp_vepu2 fdbac000.jpege-core: probing finish
[ 2.551791] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[ 2.551934] mpp-iep2 fdbb0000.iep: probe device
[ 2.552053] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[ 2.552123] mpp-iep2 fdbb0000.iep: probing finish
[ 2.552330] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[ 2.552543] mpp_jpgdec fdb90000.jpegd: probe device
[ 2.552711] mpp_jpgdec fdb90000.jpegd: probing finish
[ 2.553057] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[ 2.553115] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[ 2.553198] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[ 2.564146] rk-pcie fe150000.pcie: missing legacy IRQ resource
[ 2.564169] rk-pcie fe150000.pcie: IRQ msi not found
[ 2.564178] rk-pcie fe150000.pcie: use outband MSI support
[ 2.564188] rk-pcie fe150000.pcie: Missing *config* reg space
[ 2.564205] rk-pcie fe150000.pcie: host bridge /pcie@fe150000 ranges:
[ 2.564232] rk-pcie fe150000.pcie: err 0x00f0000000..0x00f00fffff -> 0x00f0000000
[ 2.564261] rk-pcie fe150000.pcie: IO 0x00f0100000..0x00f01fffff -> 0x00f0100000
[ 2.564282] rk-pcie fe150000.pcie: MEM 0x00f0200000..0x00f0ffffff -> 0x00f0200000
[ 2.564302] rk-pcie fe150000.pcie: MEM 0x0900000000..0x093fffffff -> 0x0900000000
[ 2.564324] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[ 2.564336] rk-pcie fe150000.pcie: Missing *config* reg space
[ 2.564368] rk-pcie fe150000.pcie: invalid resource
[ 2.564434] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[ 2.564439] rkvdec2_init:697: No niu aclk reset resource define
[ 2.564443] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[ 2.564447] rkvdec2_init:700: No niu hclk reset resource define
[ 2.564506] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[ 2.564510] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[ 2.564647] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000
[ 2.564651] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000
[ 2.564655] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520
[ 2.564660] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[ 2.564664] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[ 2.564691] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[ 2.564760] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[ 2.564989] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[ 2.565094] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[ 2.565099] rkvdec2_init:697: No niu aclk reset resource define
[ 2.565104] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[ 2.565108] rkvdec2_init:700: No niu hclk reset resource define
[ 2.565154] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[ 2.565171] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[ 2.565328] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[ 2.565332] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[ 2.565337] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[ 2.565341] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[ 2.565345] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[ 2.565373] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[ 2.565564] mpp_rkvenc2 rkvenc-ccu: probing start
[ 2.565570] mpp_rkvenc2 rkvenc-ccu: probing finish
[ 2.565683] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[ 2.565856] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[ 2.565872] mpp_rkvenc2 fdbd0000.rkvenc-core: link mode task capacity 8
[ 2.566011] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[ 2.566101] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[ 2.566169] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[ 2.566382] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[ 2.566399] mpp_rkvenc2 fdbe0000.rkvenc-core: link mode task capacity 8
[ 2.566555] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[ 2.566637] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[ 2.567145] mpp_av1dec: Adding child /av1d@fdc70000
[ 2.567369] mpp_av1dec: register device av1d-master
[ 2.567387] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[ 2.567405] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[ 2.567413] mpp_av1dec av1d-master: Adding to iommu group 17
[ 2.567630] mpp_av1dec av1d-master: probing start
[ 2.567830] mpp_av1dec av1d-master: probing finish
[ 2.567867] mpp_service mpp-srv: probe success
[ 2.575374] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 2.575384] dma-pl330 fea10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.576222] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 2.576231] dma-pl330 fea30000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.577067] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 2.577075] dma-pl330 fed10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.577504] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[ 2.577569] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[ 2.577621] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[ 2.577675] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[ 2.577723] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[ 2.578343] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 2.579095] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 2.579540] febc0000.serial: ttyS9 at MMIO 0xfebc0000 (irq = 93, base_baud = 1500000) is a 16550A
[ 2.580652] random: fast init done
[ 2.580705] random: crng init done
[ 2.581491] rockchip-vop2 fdd90000.vop: Adding to iommu group 16
[ 2.589873] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 2.589885] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 2.589900] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 2.589908] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 2.589915] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 2.589920] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 2.590122] [drm] failed to init overlay plane Cluster0-win1
[ 2.590154] [drm] failed to init overlay plane Cluster1-win1
[ 2.590183] [drm] failed to init overlay plane Cluster2-win1
[ 2.590212] [drm] failed to init overlay plane Cluster3-win1
[ 2.600401] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 2.601020] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 2.601196] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 2.601806] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 2.601976] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 2.602015] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[ 2.607727] panel-simple-dsi fde20000.dsi.0: failed to get power regulator: -517
[ 2.610214] brd: module loaded
[ 2.613415] loop: module loaded
[ 2.613609] zram: Added device: zram0
[ 2.613751] lkdtm: No crash points registered, enable through debugfs
[ 2.613841] system_heap: orders[0] = 6
[ 2.613845] system_heap: orders[1] = 4
[ 2.613849] system_heap: orders[2] = 0
[ 2.614982] ahci fe210000.sata: supply ahci not found, using dummy regulator
[ 2.615052] ahci fe210000.sata: supply phy not found, using dummy regulator
[ 2.615158] ahci fe210000.sata: supply target not found, using dummy regulator
[ 2.615220] ahci fe210000.sata: forcing port_map 0x0 -> 0x1
[ 2.615241] ahci fe210000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.615249] ahci fe210000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 2.615258] ahci fe210000.sata: port 0 can do FBS, forcing FBSCP
[ 2.615860] scsi host0: ahci
[ 2.615993] ata1: SATA max UDMA/133 mmio [mem 0xfe210000-0xfe210fff] port 0x100 irq 78
[ 2.617096] rockchip-spi feb20000.spi: no high_speed pinctrl state
[ 2.618220] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[ 2.618351] rk806 spi2.0: ON: 0x40 OFF:0x0
[ 2.619957] vdd_gpu_s0: supplied by vcc5v0_sys
[ 2.621113] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[ 2.621807] vdd_log_s0: supplied by vcc5v0_sys
[ 2.622458] vdd_vdenc_s0: supplied by vcc5v0_sys
[ 2.623124] vdd_ddr_s0: supplied by vcc5v0_sys
[ 2.623516] vdd2_ddr_s3: supplied by vcc5v0_sys
[ 2.624101] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[ 2.624636] vcc_3v3_s3: supplied by vcc5v0_sys
[ 2.625146] vddq_ddr_s0: supplied by vcc5v0_sys
[ 2.625731] vcc_1v8_s3: supplied by vcc5v0_sys
[ 2.626341] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[ 2.626939] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[ 2.627456] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 2.627975] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[ 2.628495] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 2.629097] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 2.629773] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 2.630367] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[ 2.630944] vcc_3v3_s0: supplied by vcc5v0_sys
[ 2.631465] vccio_sd_s0: supplied by vcc5v0_sys
[ 2.631995] pldo6_s3: supplied by vcc5v0_sys
[ 2.632477] rk806 spi2.0: no sleep-setting state
[ 2.632484] rk806 spi2.0: no reset-setting pinctrl state
[ 2.632489] rk806 spi2.0: no dvs-setting pinctrl state
[ 2.634558] libphy: Fixed MDIO Bus: probed
[ 2.635261] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[ 2.635409] rk_gmac-dwmac fe1c0000.ethernet: no regulator found
[ 2.635416] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[ 2.635422] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x43).
[ 2.635427] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay.
[ 2.635432] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff
[ 2.635449] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[ 2.635456] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[ 2.635462] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[ 2.635476] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[ 2.635692] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[ 2.635778] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 2.635787] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5
[ 2.635794] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[ 2.635798] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[ 2.635803] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[ 2.635808] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[ 2.635842] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[ 2.635847] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.635853] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[ 2.635858] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[ 2.635864] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[ 2.753803] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.769357] libphy: stmmac: probed
[ 2.769588] mdio_bus stmmac-1: MDIO device at address 1 is missing.
[ 2.770504] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.770567] usbcore: registered new interface driver rtl8150
[ 2.770589] usbcore: registered new interface driver r8152
[ 2.779357] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.796050] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 2.806023] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.822717] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 2.832689] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.849383] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.859356] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.876048] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.929170] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.967798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.967848] ehci-pci: EHCI PCI platform driver
[ 2.967919] ehci-platform: EHCI generic platform driver
[ 2.970628] ehci-platform fc800000.usb: EHCI Host Controller
[ 2.970827] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[ 2.970968] ehci-platform fc800000.usb: irq 19, io mem 0xfc800000
[ 2.982722] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[ 2.982960] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.982976] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.982988] usb usb1: Product: EHCI Host Controller
[ 2.983000] usb usb1: Manufacturer: Linux 5.10.66 ehci_hcd
[ 2.983011] usb usb1: SerialNumber: fc800000.usb
[ 2.983501] hub 1-0:1.0: USB hub found
[ 2.983548] hub 1-0:1.0: 1 port detected
[ 2.986537] ehci-platform fc880000.usb: EHCI Host Controller
[ 2.986719] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[ 2.986829] ehci-platform fc880000.usb: irq 21, io mem 0xfc880000
[ 2.999394] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[ 2.999614] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.999630] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.999642] usb usb2: Product: EHCI Host Controller
[ 2.999653] usb usb2: Manufacturer: Linux 5.10.66 ehci_hcd
[ 2.999664] usb usb2: SerialNumber: fc880000.usb
[ 3.000131] hub 2-0:1.0: USB hub found
[ 3.000177] hub 2-0:1.0: 1 port detected
[ 3.001117] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.001143] ohci-platform: OHCI generic platform driver
[ 3.001478] ohci-platform fc840000.usb: Generic Platform OHCI controller
[ 3.001657] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[ 3.001774] ohci-platform fc840000.usb: irq 20, io mem 0xfc840000
[ 3.060232] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 3.060258] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.060271] usb usb3: Product: Generic Platform OHCI controller
[ 3.060282] usb usb3: Manufacturer: Linux 5.10.66 ohci_hcd
[ 3.060294] usb usb3: SerialNumber: fc840000.usb
[ 3.060755] hub 3-0:1.0: USB hub found
[ 3.060803] hub 3-0:1.0: 1 port detected
[ 3.061437] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[ 3.061614] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[ 3.061720] ohci-platform fc8c0000.usb: irq 22, io mem 0xfc8c0000
[ 3.120228] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 3.120252] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.120265] usb usb4: Product: Generic Platform OHCI controller
[ 3.120276] usb usb4: Manufacturer: Linux 5.10.66 ohci_hcd
[ 3.120287] usb usb4: SerialNumber: fc8c0000.usb
[ 3.120757] hub 4-0:1.0: USB hub found
[ 3.120808] hub 4-0:1.0: 1 port detected
[ 3.122233] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 3.122416] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5
[ 3.122553] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 3.122604] xhci-hcd xhci-hcd.5.auto: irq 138, io mem 0xfcd00000
[ 3.122958] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.122974] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.122986] usb usb5: Product: xHCI Host Controller
[ 3.122997] usb usb5: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.123009] usb usb5: SerialNumber: xhci-hcd.5.auto
[ 3.123480] hub 5-0:1.0: USB hub found
[ 3.123527] hub 5-0:1.0: 1 port detected
[ 3.123884] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 3.124054] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6
[ 3.124076] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[ 3.124166] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.124306] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 3.124322] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.124333] usb usb6: Product: xHCI Host Controller
[ 3.124344] usb usb6: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.124355] usb usb6: SerialNumber: xhci-hcd.5.auto
[ 3.124829] hub 6-0:1.0: USB hub found
[ 3.124874] hub 6-0:1.0: 1 port detected
[ 3.125430] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 3.125452] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.125629] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 7
[ 3.125774] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 3.125824] xhci-hcd xhci-hcd.6.auto: irq 139, io mem 0xfc400000
[ 3.126170] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 3.126186] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.126198] usb usb7: Product: xHCI Host Controller
[ 3.126209] usb usb7: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.126220] usb usb7: SerialNumber: xhci-hcd.6.auto
[ 3.126675] hub 7-0:1.0: USB hub found
[ 3.126720] hub 7-0:1.0: 1 port detected
[ 3.127083] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 3.127244] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 8
[ 3.127267] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0 SuperSpeed
[ 3.127348] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.127491] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 3.127506] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.127518] usb usb8: Product: xHCI Host Controller
[ 3.127529] usb usb8: Manufacturer: Linux 5.10.66 xhci-hcd
[ 3.127540] usb usb8: SerialNumber: xhci-hcd.6.auto
[ 3.128029] hub 8-0:1.0: USB hub found
[ 3.128080] hub 8-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.128439] usbcore: registered new interface driver cdc_acm
[ 3.128452] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.128652] usbcore: registered new interface driver uas
[ 3.128835] usbcore: registered new interface driver usb-storage
[ 3.128938] usbcore: registered new interface driver usbserial_generic
[ 3.128970] usbserial: USB Serial support registered for generic
[ 3.129026] usbcore: registered new interface driver cp210x
[ 3.129055] usbserial: USB Serial support registered for cp210x
[ 3.129168] usbcore: registered new interface driver ftdi_sio
[ 3.129196] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.129543] usbcore: registered new interface driver keyspan
[ 3.129575] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 3.129611] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 3.129639] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 3.129667] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 3.129731] usbcore: registered new interface driver option
[ 3.129760] usbserial: USB Serial support registered for GSM modem (1-port)
[ 3.130218] usbcore: registered new interface driver oti6858
[ 3.130248] usbserial: USB Serial support registered for oti6858
[ 3.130304] usbcore: registered new interface driver pl2303
[ 3.130333] usbserial: USB Serial support registered for pl2303
[ 3.130416] usbcore: registered new interface driver qcserial
[ 3.130446] usbserial: USB Serial support registered for Qualcomm USB modem
[ 3.130550] usbcore: registered new interface driver sierra
[ 3.130580] usbserial: USB Serial support registered for Sierra USB modem
[ 3.131873] usbcore: registered new interface driver usbtouchscreen
[ 3.133702] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.3.auto/input/input0
[ 3.134328] i2c /dev entries driver
[ 3.138830] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[ 3.148059] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[ 3.157219] vdd_npu_s0: supplied by vcc5v0_sys
[ 3.163763] i2c i2c-4: 1 i2c clients have been registered at 0x68
[ 3.166990] rtc-hym8563 6-0051: rtc information is valid
[ 3.171512] rtc-hym8563 6-0051: registered as rtc0
[ 3.172739] rtc-hym8563 6-0051: hctosys: unable to read the hardware clock
[ 3.177482] ircut cam_ircut: driver version: 00.01.00
[ 3.177601] ircut cam_ircut: failed get pulse-width,use dafult value 100
[ 3.177676] ircut cam_ircut: probe successful!
[ 3.178216] rkcifhw fdce0000.rkcif: Adding to iommu group 15
[ 3.178498] rkcifhw fdce0000.rkcif: No reserved memory region assign to CIF
[ 3.178581] rkcif rkcif-mipi-lvds2: Adding to iommu group 15
[ 3.178596] rkcif rkcif-mipi-lvds2: rkcif driver version: v00.01.0a
[ 3.178645] rkcif rkcif-mipi-lvds2: attach to cif hw node
[ 3.178650] rkcif rkcif-mipi-lvds2: rkcif wait line 0
[ 3.178656] : terminal subdev does not exist
[ 3.178661] : terminal subdev does not exist
[ 3.178665] : terminal subdev does not exist
[ 3.178668] : terminal subdev does not exist
[ 3.178674] : get_remote_sensor: video pad[0] is null
[ 3.178678] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.178684] : get_remote_sensor: video pad[0] is null
[ 3.178688] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.178692] : get_remote_sensor: video pad[0] is null
[ 3.178696] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.178701] : get_remote_sensor: video pad[0] is null
[ 3.178705] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 3.180593] rkcif rkcif-mipi-lvds2: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 3.180602] rockchip-mipi-csi2: Async registered subdev
[ 3.180612] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds2!
[ 3.181146] rkisp_hw fdcb0000.rkisp: Adding to iommu group 14
[ 3.181305] rkisp_hw fdcb0000.rkisp: is_thunderboot: 0
[ 3.181311] rkisp_hw fdcb0000.rkisp: max input:0x0@0fps
[ 3.181316] rkisp_hw fdcb0000.rkisp: Missing rockchip,grf property
[ 3.181400] rkisp_hw fdcb0000.rkisp: no find phandle sram
[ 3.181804] rkisp rkisp0-vir0: rkisp driver version: v01.09.00
[ 3.181941] rkisp rkisp0-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 3.183095] usbcore: registered new interface driver uvcvideo
[ 3.183100] USB Video Class driver (1.1.1)
[ 3.184290] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[ 3.184792] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[ 3.185123] Bluetooth: HCI UART driver ver 2.3
[ 3.185129] Bluetooth: HCI UART protocol H4 registered
[ 3.185134] Bluetooth: HCI UART protocol ATH3K registered
[ 3.185163] usbcore: registered new interface driver bfusb
[ 3.185191] usbcore: registered new interface driver btusb
[ 3.185542] cpu cpu0: leakage=12
[ 3.187028] cpu cpu0: pvtm=1510
[ 3.187120] cpu cpu0: pvtm-volt-sel=5
[ 3.187633] cpu cpu4: leakage=10
[ 3.194149] cpu cpu4: pvtm=1746
[ 3.198091] cpu cpu4: pvtm-volt-sel=6
[ 3.199339] cpu cpu6: leakage=11
[ 3.205881] cpu cpu6: pvtm=1746
[ 3.209845] cpu cpu6: pvtm-volt-sel=6
[ 3.211443] cpu cpu0: avs=0
[ 3.212112] cpu cpu4: avs=0
[ 3.212789] cpu cpu6: avs=0
[ 3.213016] cpu cpu0: EM: created perf domain
[ 3.213070] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0
[ 3.213668] cpu cpu4: EM: created perf domain
[ 3.213713] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 3.222103] cpu cpu6: EM: created perf domain
[ 3.222511] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 3.238187] sdhci: Secure Digital Host Controller Interface driver
[ 3.238215] sdhci: Copyright(c) Pierre Ossman
[ 3.238224] Synopsys Designware Multimedia Card Interface Driver
[ 3.239421] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.239898] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 3.239922] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 3.239933] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 3.239978] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 80,32 bit host data width,256 deep fifo
[ 3.240096] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[ 3.240130] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[ 3.240142] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[ 3.240184] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 79,32 bit host data width,256 deep fifo
[ 3.240362] dwmmc_rockchip fe2d0000.mmc: allocated mmc-pwrseq
[ 3.240380] mmc_host mmc1: card is non-removable.
[ 3.241553] dwmmc_rockchip fe2c0000.mmc: Failed getting OCR mask: -22
[ 3.241743] dwmmc_rockchip fe2c0000.mmc: could not set regulator OCR (-22)
[ 3.241752] dwmmc_rockchip fe2c0000.mmc: failed to enable vmmc regulator
[ 3.241862] leds-gpio: probe of leds failed with error -16
[ 3.242037] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 3.242108] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 3.243459] cryptodev: driver 1.12 loaded.
[ 3.243515] hid: raw HID events driver (C) Jiri Kosina
[ 3.243935] usbcore: registered new interface driver usbhid
[ 3.243952] usbhid: USB HID core driver
[ 3.247816] optee: probing for conduit method.
[ 3.247835] optee: revision 3.13 (87d94c5e)
[ 3.248173] optee: initialized driver
[ 3.248747] usbcore: registered new interface driver snd-usb-audio
[ 3.250284] ES8323 7-0011: i2c recv Failed
[ 3.256223] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 3.260726] Initializing XFRM netlink socket
[ 3.261123] NET: Registered protocol family 10
[ 3.261956] Segment Routing with IPv6
[ 3.262012] NET: Registered protocol family 17
[ 3.262031] NET: Registered protocol family 15
[ 3.262185] Bluetooth: RFCOMM socket layer initialized
[ 3.262211] Bluetooth: RFCOMM ver 1.11
[ 3.262224] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.262235] Bluetooth: HIDP socket layer initialized
[ 3.262275] [BT_RFKILL]: Enter rfkill_rk_init
[ 3.262283] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 3.262646] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 3.262676] [WLAN_RFKILL]: can't find rockchip,grf property
[ 3.262703] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ 3.262711] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 3.262718] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 3.262773] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 20 flags = 0.
[ 3.262801] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 10, flags = 0.
[ 3.262811] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 3.262819] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 3.262827] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 3.262834] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 3.263521] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 148.
[ 3.263549] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 22.
[ 3.263566] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 21.
[ 3.263582] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 0.
[ 3.263632] [BT_RFKILL]: Request irq for bt wakeup host
[ 3.263706] [BT_RFKILL]: ** disable irq
[ 3.263781] [BT_RFKILL]: bt_default device registered.
[ 3.263858] Key type dns_resolver registered
[ 3.264758] imx415 3-001a: driver version: 00.01.07
[ 3.264774] imx415 3-001a: Get hdr mode failed! no hdr default
[ 3.264803] imx415 3-001a: Failed to get reset-gpios
[ 3.264824] imx415 3-001a: Failed to get power-gpios
[ 3.264835] imx415 3-001a: could not get default pinstate
[ 3.264843] imx415 3-001a: could not get sleep pinstate
[ 3.264893] imx415 3-001a: supply dvdd not found, using dummy regulator
[ 3.265015] imx415 3-001a: supply dovdd not found, using dummy regulator
[ 3.272902] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[ 3.312496] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[ 3.313295] mmcblk0: mmc0:0001 A3A561 57.6 GiB
[ 3.313536] mmcblk0boot0: mmc0:0001 A3A561 partition 1 4.00 MiB
[ 3.313743] mmcblk0boot1: mmc0:0001 A3A561 partition 2 4.00 MiB
[ 3.313925] mmcblk0rpmb: mmc0:0001 A3A561 partition 3 16.0 MiB, chardev (236:0)
[ 3.317472] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 3.333507] imx415 3-001a: Unexpected sensor id(000000), ret(-5)
[ 3.334681] Loading compiled-in X.509 certificates
[ 3.335577] pstore: Using crash dump compression: deflate
[ 3.335950] rga3_core0 fdb60000.rga: Adding to iommu group 2
[ 3.336260] rga: rga3_core0_irq, irq = 34, match scheduler
[ 3.336814] rga: rga3_core0 driver loaded successfully ver:3.0.76831
[ 3.336844] rga: rga3_core0 probe successfully
[ 3.337452] rga3_core1 fdb70000.rga: Adding to iommu group 3
[ 3.337705] rga: rga3_core1_irq, irq = 35, match scheduler
[ 3.338175] rga: rga3_core1 driver loaded successfully ver:3.0.76831
[ 3.338202] rga: rga3_core1 probe successfully
[ 3.338747] rga: rga2_irq, irq = 36, match scheduler
[ 3.339216] rga: rga2 driver loaded successfully ver:3.2.63318
[ 3.339234] rga: rga2 probe successfully
[ 3.339803] rga: Module initialized. v1.2.14
[ 3.381373] mali fb000000.gpu: Kernel DDK version g12p0-01eac0
[ 3.381996] mali fb000000.gpu: leakage=20
[ 3.383407] mali fb000000.gpu: pvtm=922
[ 3.383456] mali fb000000.gpu: pvtm-volt-sel=5
[ 3.384235] mali fb000000.gpu: avs=0
[ 3.385774] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 136; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 3.386705] mali fb000000.gpu: GPU hardware issue table may need updating:
[ 3.386705] r0p0 status 5 is unknown; treating as r0p0 status 0
[ 3.386726] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[ 3.386818] mali fb000000.gpu: No priority control manager is configured
[ 3.386830] mali fb000000.gpu: No memory group manager is configured
[ 3.386854] mali fb000000.gpu: Protected memory allocator not available
[ 3.387066] vendor storage:20190527 ret = 0
[ 3.387997] mali fb000000.gpu: Couldn't find power_model DT node matching 'arm,mali-simple-power-model'
[ 3.388012] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.static-coefficient = 1*[0]
[ 3.388206] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.dynamic-coefficient = 1*[0]
[ 3.388389] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.ts = 4*[0]
[ 3.388572] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.thermal-zone = ''
[ 3.391291] mali fb000000.gpu: Using configured power model mali-lodx-power-model, and fallback mali-simple-power-model
[ 3.391457] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 3.392753] mali fb000000.gpu: Probed as mali0
[ 3.459907] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 3.473752] pcie20_avdd0v85: supplied by vdd_0v85_s0
[ 3.475876] pcie20_avdd1v8: supplied by avcc_1v8_s0
[ 3.477698] pcie30_avdd0v75: supplied by avdd_0v75_s0
[ 3.479098] pcie30_avdd1v8: supplied by avcc_1v8_s0
[ 3.480543] vcc3v3_lcd0_n: supplied by vcc_1v8_s0
[ 3.500020] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 3.500093] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 3.500148] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 3.500180] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 3.500207] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 3.500232] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 3.501058] [drm] failed to init overlay plane Cluster0-win1
[ 3.501177] [drm] failed to init overlay plane Cluster1-win1
[ 3.501292] [drm] failed to init overlay plane Cluster2-win1
[ 3.501411] [drm] failed to init overlay plane Cluster3-win1
[ 3.540546] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 3.543160] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 3.544803] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 3.547184] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 3.548811] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 3.548878] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[ 3.556424] input: adc-keys as /devices/platform/adc-keys/input/input1
[ 3.557026] <<GTP-INF>>[gt1x_ts_probe:537] GTP Driver Version: V1.4<2015/07/10>
[ 3.557034] <<GTP-INF>>[gt1x_ts_probe:538] GTP I2C Address: 0x14
[ 3.557128] <<GTP-ERR>>[gt1x_parse_dt:334] vdd_ana not specified, fallback to power-supply
[ 3.558432] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 3.983479] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 4.483497] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 4.490307] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 4.490326] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 4.490346] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 4.490357] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 4.490367] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2
[ 4.490375] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2
[ 4.490631] [drm] failed to init overlay plane Cluster0-win1
[ 4.490669] [drm] failed to init overlay plane Cluster1-win1
[ 4.490705] [drm] failed to init overlay plane Cluster2-win1
[ 4.490741] [drm] failed to init overlay plane Cluster3-win1
[ 4.508657] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010fb0f30)
[ 4.511443] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 4.513154] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010fb8c90)
[ 4.515875] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 4.517624] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010fb8c90)
[ 4.517752] rockchip-drm display-subsystem: bound fde20000.dsi (ops 0xffffffc010fbab90)
[ 4.517842] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffffffc010fbafa0)
[ 4.517909] rockchip-drm display-subsystem: bound fde60000.dp (ops 0xffffffc010fbafa0)
[ 4.656152] rk3x-i2c fead0000.i2c: timeout, ipd: 0x90, state: 3
[ 4.656302] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 4.656335] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 4.656360] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 4.671814] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.672494] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.673238] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.674136] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.675044] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.675162] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 4.675490] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 4.675544] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 4.675723] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 4.675769] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 4.703041] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 4.725973] rockchip-vop2 fdd90000.vop: [drm:vop2_setup_layer_mixer_for_vp] *ERROR* wait layer cfg done timeout: 0x75643102--0x75641302
[ 4.877233] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.877664] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.878085] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.878407] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.878728] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 4.878742] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 4.908246] dw-dp fde50000.dp: failed to probe DP link: -110
[ 4.917138] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[ 5.227133] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 5.426099] rk-pcie fe170000.pcie: PCIe Link Fail
[ 5.426116] rk-pcie fe170000.pcie: failed to initialize host
[ 5.439426] rk-pcie fe150000.pcie: PCIe Link Fail
[ 5.439441] rk-pcie fe150000.pcie: failed to initialize host
[ 5.727150] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 5.728504] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[ 5.730849] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card1/input2
[ 5.733259] input: rockchip-hdmi1 rockchip-hdmi1 as /devices/platform/hdmi1-sound/sound/card2/input3
[ 5.737194] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1
[ 5.737219] rockchip-csi2-dphy0: No link between dphy and sensor
[ 5.737707] rockchip-csi2-dphy0: No link between dphy and sensor
[ 5.737734] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 5.737746] rkcif-mipi-lvds2: Async subdev notifier completed
[ 5.737753] rockchip-csi2-dphy0: No link between dphy and sensor
[ 5.737764] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 5.737770] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 5.737891] rockchip-csi2-dphy0: No link between dphy and sensor
[ 5.737940] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 5.737952] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 5.738793] RKNPU fdab0000.npu: Adding to iommu group 0
[ 5.738970] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 5.740316] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[ 5.740342] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[ 5.740356] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[ 5.740840] [drm] Initialized rknpu 0.7.2 20220428 for fdab0000.npu on minor 1
[ 5.743029] RKNPU fdab0000.npu: leakage=11
[ 5.749387] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 5.749406] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 5.749413] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 5.749419] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 5.750493] RKNPU fdab0000.npu: pvtm=916
[ 5.754868] RKNPU fdab0000.npu: pvtm-volt-sel=5
[ 5.755554] RKNPU fdab0000.npu: avs=0
[ 5.755696] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 5.765875] RKNPU fdab0000.npu: failed to find power_model node
[ 5.765891] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[ 5.765898] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[ 5.767046] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.769371] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.770175] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 5.770190] cfg80211: failed to load regulatory.db
[ 5.770544] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 5.771967] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 405; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '15:54:43', on 'Jul 3 2024'.
[ 5.772323] Mali:
[ 5.772326] Mali device driver loaded
[ 5.772339] rkisp rkisp0-vir0: clear unready subdev num: 1
[ 5.772507] rkisp0-vir0: Async subdev notifier completed
[ 5.772516] ALSA device list:
[ 5.772522] #0: rockchip,hdmiin
[ 5.772528] #1: rockchip-hdmi0
[ 5.772533] #2: rockchip-hdmi1
[ 5.946230] mmc_host mmc1: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 6.473856] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 6.842758] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 6.842776] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 6.842783] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 6.842789] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 6.973878] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 7.193029] mmc_host mmc1: Bus speed (slot 0) = 187500Hz (slot req 100000Hz, actual 93750HZ div = 1)
[ 7.733116] dwmmc_rockchip fe2d0000.mmc: Busy; trying anyway
[ 7.936043] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 7.936061] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 7.936068] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 7.936074] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[ 8.233132] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[ 9.029689] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 9.029757] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 9.029787] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[ 9.029812] <<GTP-ERR>>[gt1x_init:2341] Init failed, use default setting
[ 10.043116] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 10.043202] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 10.043232] <<GTP-ERR>>[gt1x_get_chip_type:891] I2c communication error.
[ 10.043258] <<GTP-ERR>>[gt1x_init:2351] Get chip type failed!
[ 11.056411] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 11.056503] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 11.056533] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 12.176295] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 12.176383] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 12.176413] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 13.296282] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 3
[ 13.296370] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-110)
[ 13.296400] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[ 13.403061] <<GTP-INF>>[gt1x_read_version:859] IC VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID)
[ 13.403143] <<GTP-INF>>[gt1x_init_panel:604] Config group0 used, length:239
[ 13.403176] <<GTP-INF>>[gt1x_init_panel:655] X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1
[ 14.416403] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 14.416493] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 15.429663] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 15.429752] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 16.443000] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 16.443091] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 17.456289] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 17.456379] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 18.469796] rk3x-i2c fead0000.i2c: timeout, ipd: 0x80, state: 2
[ 18.469887] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-110)
[ 18.469918] <<GTP-ERR>>[gt1x_send_cfg:549] Send config failed!
[ 18.469943] <<GTP-ERR>>[gt1x_init:2363] Init panel failed.
[ 18.470584] <<GTP-ERR>>[gt1x_ts_probe:564] GTP init failed!!!
[ 18.470751] Goodix-TS-GT1X: probe of 5-0014 failed with error -2147483644
[ 18.479932] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ 18.479994] VFS: Mounted root (ext4 filesystem) on device 179:6.
[ 18.480876] devtmpfs: mounted
[ 18.483963] Freeing unused kernel memory: 6272K
[ 18.506253] Run /sbin/init as init process
[ 18.556000] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
mount: mounting PARTLABEL=oem on /oem failed: No such file or directory
mount: mounting PARTLABEL=userdata on /userdata failed: No such file or directory
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
/usr/bin/modetest
[ 18.764199] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.764634] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.765024] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.765461] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.765850] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.766256] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.766279] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 18.797711] dw-dp fde50000.dp: failed to probe DP link: -110
[ 18.963444] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.965643] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.970283] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.972996] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.983080] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.983752] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 18.983798] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.015644] dw-dp fde50000.dp: failed to probe DP link: -110
[ 19.181775] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.182394] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.183102] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.186117] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.189308] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.190105] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.190169] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.222864] dw-dp fde50000.dp: failed to probe DP link: -110
[ 19.387147] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.389786] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.396058] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.409448] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.413092] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.414184] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.414292] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.445366] dw-dp fde50000.dp: failed to probe DP link: -110
[ 19.593092] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.596455] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.602005] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.607022] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.615781] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.615894] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.647671] dw-dp fde50000.dp: failed to probe DP link: -110
[ 19.818270] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.819021] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.822787] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.826119] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.827179] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.827943] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.828062] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.861245] dw-dp fde50000.dp: failed to probe DP link: -110
[ 20.022376] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.026335] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.027220] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.027553] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.028037] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.029429] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.029507] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.062158] dw-dp fde50000.dp: failed to probe DP link: -110
[ 20.232091] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.232857] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.233792] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.236752] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.238200] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.239278] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.239547] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.274260] dw-dp fde50000.dp: failed to probe DP link: -110
[ 20.438539] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.439225] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.442815] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.446383] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.449730] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.453076] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 20.453185] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 20.485197] dw-dp fde50000.dp: failed to probe DP link: -110
Populating /dev using udev: [ 20.509843] udevd[314]: starting version 3.2.10
[ 20.526525] udevd[315]: starting eudev-3.2.10
[ 20.632586] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.632822] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.632868] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 20.632875] stream_cif_mipi_id1: update sensor info failed -19
[ 20.632925] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.633303] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.633321] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 20.633324] rkcif_scale_ch2: update sensor info failed -19
[ 20.633454] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 20.633458] rkcif_scale_ch3: update sensor info failed -19
[ 20.633534] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.633555] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 20.633562] stream_cif_mipi_id3: update sensor info failed -19
[ 20.633595] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 20.633599] stream_cif_mipi_id0: update sensor info failed -19
[ 20.634564] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.634581] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 20.634584] rkcif_tools_id2: update sensor info failed -19
[ 20.635096] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.635174] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.635188] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 20.635192] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.635196] rkcif_scale_ch1: update sensor info failed -19
[ 20.635209] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 20.635218] rkcif_tools_id1: update sensor info failed -19
[ 20.635279] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 20.635283] rkcif_scale_ch0: update sensor info failed -19
[ 20.647190] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.647192] rockchip-csi2-dphy0: No link between dphy and sensor
[ 20.647215] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 20.647220] stream_cif_mipi_id2: update sensor info failed -19
[ 20.647222] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 20.647223] rkcif_tools_id0: update sensor info failed -19
done
Saving random seed: OK
Will now mount all partitions in /etc/fstab
Note: Will skip fsck, remove /.skip_fsck to enable
Handling rootfs: /dev/mmcblk0p6 / ext4 rw,noauto 1
Resizing /dev/mmcblk0p6(ext4)
resize2fs 1.46.4 (18-Aug-2021)
[ 20.940203] EXT4-fs (mmcblk0p6): resizing filesystem from 248582 to 3670016 blocks
[ 20.991160] EXT4-fs (mmcblk0p6): resized filesystem to 3670016
Filesystem at /dev/mmcblk0p6 is mounted on /tmp/tmp.PFxx80glhE; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 1
The filesystem on /dev/mmcblk0p6 is now 3670016 (4k) blocks long.
tune2fs 1.46.4 (18-Aug-2021)
Handling oem: /dev/mmcblk0p7 /oem ext2 defaults 2
Resizing /dev/mmcblk0p7(ext2)
[ 21.348423] EXT4-fs (mmcblk0p7): mounting ext2 file system using the ext4 subsystem
[ 21.350098] EXT4-fs (mmcblk0p7): mounted filesystem without journal. Opts: (null)
resize2fs 1.46.4 (18-Aug-2021)
The filesystem is already 131072 (1k) blocks long. Nothing to do!
tune2fs 1.46.4 (18-Aug-2021)
Mounting /dev/mmcblk0p7(ext2) on /oem
[ 21.377721] EXT4-fs (mmcblk0p7): mounting ext2 file system using the ext4 subsystem
[ 21.379229] EXT4-fs (mmcblk0p7): mounted filesystem without journal. Opts: (null)
Handling userdata: /dev/mmcblk0p8 /userdata ext2 defaults 2
Resizing /dev/mmcblk0p8(ext2)
[ 21.510655] EXT4-fs (mmcblk0p8): mounting ext2 file system using the ext4 subsystem
[ 21.515544] EXT4-fs (mmcblk0p8): warning: mounting unchecked fs, running e2fsck is recommended
[ 21.531321] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null)
resize2fs 1.46.4 (18-Aug-2021)
The filesystem is already 45359072 (1k) blocks long. Nothing to do!
tune2fs 1.46.4 (18-Aug-2021)
Mounting /dev/mmcblk0p8(ext2) on /userdata
[ 21.560853] EXT4-fs (mmcblk0p8): mounting ext2 file system using the ext4 subsystem
[ 21.565276] EXT4-fs (mmcblk0p8): warning: mounting unchecked fs, running e2fsck is recommended
[ 21.583267] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null)
Log saved to /tmp/mountall.log
Starting system message bus: done
/etc/init.d/S36load_wifi_modules: line 6: /sys/class/rfkill/rfkill1/state: No such file or directory
wpa_supplicant.conf init
wpa_supplicant.conf init
[ 21.713166] bcmdhd: Unknown symbol dhd_wlan_mem_prealloc (err -2)
[ 21.762853] bcmdhd: Unknown symbol dhd_wlan_mem_prealloc (err -2)
insmod: can't insert '/system/lib/modules/bcmdhd.ko': unknown symbol in module, or unknown parameter
Starting bluetoothd: OK
Starting network: OK
Starting dhcpcd...
dhcpcd-9.4.1 starting
dev: loaded udev
no interfaces have a carrier
forked to background, child pid 800
[ 21.948792] rk_gmac-dwmac fe1c0000.ethernet eth0: no phy at addr -1
[ 21.948823] rk_gmac-dwmac fe1c0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
Starting ntpd: OK
starting weston... done.
Starting dropbear sshd: OK
Starting pulseaudio: OK
Debug: configfs_init
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac1.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac2.gs0': No such file or directory
[ 22.083907] file system registered
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/rndis.gs0': No such file or directory
[ 22.106205] Mass Storage Function, version: 2009/09/11
[ 22.106282] LUN: removable file: (no medium)
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/hid.usb0': No such file or directory
[ 22.151207] read descriptors
[ 22.151254] read strings
Date: 1970-01-01 UTC
[00:00:20.084] weston 10.0.0
https://wayland.freedesktop.org
Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
Build: linux-5.10-gen-rkr3.1
[00:00:20.085] Command line: /usr/bin/weston
[00:00:20.085] OS: Linux, 5.10.66, #1 SMP Wed Jul 3 15:52:23 CST 2024, aarch64
[00:00:20.086] Flight recorder: enabled
[00:00:20.086] warning: XDG_RUNTIME_DIR "/var/run" is not configured
correctly. Unix access mode must be 0700 (current mode is 0755),
and must be owned by the user UID 0 (current owner is UID 0).
Refer to your distribution on how to get it, or
http://www.freedesktop.org/wiki/Specifications/basedir-spec
on how to implement it.
[00:00:20.090] Using config file '/etc/xdg/weston/weston.ini'
[00:00:20.090] Output repaint window is -1 ms maximum.
[00:00:20.091] Loading module '/usr/lib/libweston-10/drm-backend.so'
[00:00:20.094] initializing drm backend
[00:00:20.094] Entering mirror mode.
[00:00:20.094] Trying weston_launch launcher...
[00:00:20.094] could not get launcher fd from env
[00:00:20.095] Trying direct launcher...
[00:00:20.097] using /dev/dri/card0
[00:00:20.097] DRM: does not support atomic modesetting
[00:00:20.098] DRM: does not support GBM modifiers
[00:00:20.098] DRM: supports picture aspect ratio
[00:00:20.099] Loading module '/usr/lib/libweston-10/gl-renderer.so'
[00:00:20.102] EGL client extensions: EGL_EXT_client_extensions
EGL_EXT_platform_base EGL_KHR_client_get_all_proc_addresses
EGL_KHR_platform_gbm EGL_KHR_platform_wayland
EGL_EXT_platform_wayland
arm_release_ver of this libmali is 'g6p0-01eac0', rk_so_ver is '6'.
[ 22.184110] mali fb000000.gpu: Loading Mali firmware 0x1010000
[ 22.184625] mali fb000000.gpu: Protected memory allocator not found, Firmware protected mode entry will not be supported
[ 22.184642] mali fb000000.gpu: Protected memory allocator not found, Firmware protected mode entry will not be supported
[ 22.184649] mali fb000000.gpu: Protected memory allocator not found, Firmware protected mode entry will not be supported
W: [pulseaudio] authkey.c: Failed to open cookie file '//.config/pulse/cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to load authentication key '//.config/pulse/cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to open cookie file '//.pulse-cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to load authentication key '//.pulse-cookie': No such file or directory
[00:00:20.122] EGL version: 1.4 Valhall-"g6p0-01eac0"
[00:00:20.122] EGL vendor: ARM
[00:00:20.122] EGL client APIs: OpenGL_ES
[00:00:20.122] EGL extensions: EGL_WL_bind_wayland_display
EGL_NV_context_priority_realtime EGL_KHR_partial_update
EGL_KHR_config_attribs EGL_KHR_image EGL_KHR_image_base
EGL_KHR_fence_sync EGL_KHR_wait_sync EGL_KHR_gl_colorspace
EGL_KHR_get_all_proc_addresses EGL_IMG_context_priority
EGL_KHR_no_config_context EGL_EXT_image_dma_buf_import
EGL_EXT_image_dma_buf_import_modifiers EGL_EXT_yuv_surface
EGL_EXT_pixel_format_float EGL_ARM_pixmap_multisample_discard
EGL_KHR_gl_texture_2D_image EGL_KHR_gl_renderbuffer_image
EGL_KHR_create_context EGL_KHR_surfaceless_context
EGL_KHR_gl_texture_cubemap_image EGL_EXT_image_gl_colorspace
EGL_EXT_create_context_robustness
[00:00:20.129] warning: Disabling render GPU timeline and explicit synchronization due to missing EGL_ANDROID_native_fence_sync extension
[00:00:20.130] EGL_KHR_surfaceless_context available
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
[00:00:20.147] GL version: OpenGL ES 3.2 v1.g6p0-01eac0.ba52c908d926792b8f5fe28f383a2b03
[00:00:20.148] GLSL version: OpenGL ES GLSL ES 3.20
[00:00:20.148] GL vendor: ARM
[00:00:20.148] GL renderer: Mali-LODX
[00:00:20.149] GL extensions: GL_ARM_rgba8 GL_ARM_mali_shader_binary
GL_OES_depth24 GL_OES_depth_texture
GL_OES_depth_texture_cube_map GL_OES_packed_depth_stencil
GL_OES_rgb8_rgba8 GL_EXT_read_format_bgra
GL_OES_compressed_paletted_texture
GL_OES_compressed_ETC1_RGB8_texture GL_OES_standard_derivatives
GL_OES_EGL_image GL_OES_EGL_image_external
GL_OES_EGL_image_external_essl3W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
GL_OES_EGL_syncW: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
GL_OES_texture_npot GL_OES_vertex_half_float
GL_OES_required_internalformat GL_OES_vertex_array_object
GL_OES_mapbuffer GL_EXT_texture_format_BGRA8888
GL_EXT_texture_rg GL_EXT_texture_type_2_10_10_10_REV
GL_OES_fbo_render_mipmap GL_OES_element_index_uint
GL_EXT_shadow_samplers GL_OES_texture_compression_astc
GL_KHR_texture_compression_astc_ldr
GL_KHR_texture_compression_astc_hdr
GL_KHR_texture_compression_astc_sliced_3d
GL_EXT_texture_compression_astc_decode_mode
GL_EXT_texture_compression_astc_decode_mode_rgb9e5 GL_KHR_debug
GL_EXT_occlusion_query_boolean GL_EXT_disjoint_timer_query
GL_EXT_blend_minmax GL_EXT_discard_framebuffer
GL_OES_get_program_binary GL_OES_texture_3D
GL_EXT_texture_storage GL_EXT_multisampled_render_to_texture
GL_EXT_multisampled_render_to_texture2
GL_OES_surfaceless_context GL_OES_texture_stencil8
GL_EXT_shader_pixel_local_storage
GL_ARM_shader_framebuffer_fetch
GL_ARM_shader_framebuffer_fetch_depth_stencil
GL_ARM_mali_program_binary GL_EXT_sRGB
GL_EXT_sRGB_write_control GL_EXT_texture_sRGB_decode
GL_EXT_texture_sRGB_R8 GL_EXT_texture_sRGB_RG8
GL_KHR_blend_equation_advanced
GL_KHR_blend_equation_advanced_coherent
GL_OES_texture_storage_multisample_2d_array
GL_OES_shader_image_atomic GL_EXT_robustness
GL_EXT_draw_buffers_indexed GL_OES_draw_buffers_indexed
GL_EXT_texture_border_clamp GL_OES_texture_border_clamp
GL_EXT_texture_cube_map_array GL_OES_texture_cube_map_array
GL_OES_sample_variables GL_OES_sample_shading
GL_OES_shader_multisample_interpolation GL_EXT_shader_io_blocks
GL_OES_shader_io_blocks GL_EXT_tessellation_shader
GL_OES_tessellation_shader GL_EXT_primitive_bounding_box
GL_OES_primitive_bounding_box GL_EXT_geometry_shader
GL_OES_geometry_shader GL_ANDROID_extension_pack_es31a
GL_EXT_gpu_shader5 GL_OES_gpu_shader5 GL_EXT_texture_buffer
GL_OES_texture_buffer GL_EXT_copy_image GL_OES_copy_image
GL_EXT_shader_non_constant_global_initializers
GL_EXT_color_buffer_half_float GL_EXT_unpack_subimage
GL_EXT_color_buffer_float GL_EXT_float_blend GL_EXT_YUV_target
GL_OVR_multiview GL_OVR_multiview2
GL_OVR_multiview_multisampled_render_to_texture
GL_KHR_robustness GL_KHR_robust_buffer_access_behavior
GL_EXT_draw_elements_base_vertex
GL_OES_draw_elements_base_vertex GL_EXT_buffer_storage
GL_EXT_texture_filter_anisotropic GL_OES_texture_float_linear
GL_ARM_texture_unnormalized_coordinates
GL_EXT_shader_framebuffer_fetch
[00:00:20.270] GL ES 3.2 - renderer features:
read-back format: BGRA
wl_shm sub-image to texture: yes
EGL Wayland extension: yes
[00:00:20.271] couldn't fstat launcher tty: Bad file descriptor
[00:00:20.288] event1 - adc-keys: is tagged by udev as: Keyboard
[00:00:20.288] event1 - adc-keys: device is a keyboard
[00:00:20.289] event0 - rk805 pwrkey: is tagged by udev as: Keyboard
[00:00:20.290] event0 - rk805 pwrkey: device is a keyboard
[00:00:20.291] event2 - rockchip-hdmi0 rockchip-hdmi0: is tagged by udev as: Switch
[00:00:20.323] event2 - not using input device '/dev/input/event2'
[00:00:20.326] event3 - rockchip-hdmi1 rockchip-hdmi1: is tagged by udev as: Switch
[00:00:20.373] event3 - not using input device '/dev/input/event3'
[00:00:20.420] libinput: configuring device "adc-keys".
[00:00:20.420] libinput: configuring device "rk805 pwrkey".
[00:00:20.555] DRM: head 'HDMI-A-1' updated, connector 185 is connected, EDID make 'GSM', model '27MP35', serial 'unknown'
[00:00:20.556] DRM: head 'HDMI-A-1' found, connector 185 is connected, EDID make 'GSM', model '27MP35', serial 'unknown'
[ 22.642815] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 22.644406] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 22.646492] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 22.649724] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 22.650404] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 22.650467] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[00:00:20.578] DRM: head 'HDMI-A-2' updated, connector 195 is connected, EDID make 'unknown', model 'unknown', serial 'unknown'
[00:00:20.579] DRM: head 'HDMI-A-2' found, connector 195 is connected, EDID make 'unknown', model 'unknown', serial 'unknown'
[00:00:20.581] DRM: head 'DSI-1' updated, connector 205 is connected, EDID make 'unknown', model 'unknown', serial 'unknown'
[00:00:20.582] DRM: head 'DSI-1' found, connector 205 is connected, EDID make 'unknown', model 'unknown', serial 'unknown'
[ 22.686609] dw-dp fde50000.dp: failed to probe DP link: -110
[00:00:20.614] DRM: head 'DP-1' updated, connector 208 is disconnected.
[00:00:20.614] DRM: head 'DP-1' found, connector 208 is disconnected.
[00:00:20.615] DRM: head 'DP-2' updated, connector 214 is disconnected.
[00:00:20.615] DRM: head 'DP-2' found, connector 214 is disconnected.
[00:00:20.616] Registered plugin API 'weston_drm_output_api_v1' of size 24
[00:00:20.616] Color manager: no-op
[00:00:20.617] Output 'HDMI-A-1' using color profile: built-in default sRGB SDR profile
[00:00:20.618] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:20.619] Output HDMI-A-1 (crtc 68) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1600x900@60.0, 108.0 MHz
1280x1024@60.0, 108.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
800x600@75.0, 49.5 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
[00:00:20.624] associating input device event1 with output HDMI-A-1 (none by udev)
[00:00:20.625] associating input device event0 with output HDMI-A-1 (none by udev)
[00:00:20.626] Output HDMI-A-1 changed to mirror output
[00:00:20.626] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[00:00:20.626] Output 'HDMI-A-2' using color profile: built-in default sRGB SDR profile
[00:00:20.627] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:20.628] Output HDMI-A-2 (crtc 85) video modes:
1920x1080@60.0 16:9, preferred, current, 148.5 MHz
1920x1080@50.0 16:9, 148.5 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1920x1080@60.0, preferred, 148.5 MHz
[00:00:20.631] associating input device event1 with output HDMI-A-2 (none by udev)
[00:00:20.631] associating input device event0 with output HDMI-A-2 (none by udev)
[00:00:20.632] Output HDMI-A-2 changed to mirror output
[00:00:20.632] Output 'HDMI-A-2' enabled with head(s) HDMI-A-2
[00:00:20.633] Output 'DSI-1' using color profile: built-in default sRGB SDR profile
[00:00:20.634] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:20.635] Output DSI-1 (crtc 119) video modes:
1080x1920@59.9, preferred, current, 132.0 MHz
[00:00:20.635] associating input device event1 with output DSI-1 (none by udev)
[00:00:20.636] associating input device event0 with output DSI-1 (none by udev)
[00:00:20.637] Output 'DSI-1' enabled with head(s) DSI-1
[00:00:20.637] Compositor capabilities:
arbitrary surface rotation: yes
screen capture uses y-flip: yes
cursor planes: yes
arbitrary resolutions: no
view mask clipping: yes
explicit sync: no
color operations: yes
presentation clock: CLOCK_MONOTONIC, id 1
presentation clock resolution: 0.000000001 s
[00:00:20.646] Loading module '/usr/lib/weston/desktop-shell.so'
[00:00:20.650] launching '/usr/libexec/weston-keyboard'
[00:00:20.654] Note: support for the deprecated wl_shell interface is disabled. If a legacy client still needs it, it can be re-enabled by passing -Ddeprecated-wl-shell=true to Meson when building Weston.
[00:00:20.656] launching '/usr/libexec/weston-desktop-shell'
[ 22.774616] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 22.774799] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
[ 22.805980] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:1000) for vp1 dclk: 148500000
[ 22.806097] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] dclk_out1 div: 0 dclk_core1 div: 2
[ 22.806121] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] set dclk_vop1 to 148500000, get 148500000
[ 22.806158] dwhdmi-rockchip fdea0000.hdmi: final tmdsclk = 148500000
[ 22.806175] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: bus_width:0x16a8c8,bit_rate:1485000
[ 22.806294] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy lane locked!
[ 22.806333] dwhdmi-rockchip fdea0000.hdmi: don't use dsc mode
[ 23.012872] dwhdmi-rockchip fdea0000.hdmi: dw hdmi qp use tmds mode
[ 23.023551] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 23.075292] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 23.088808] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 23.145749] Freeing drm_logo memory: 732K
Starting dnsmasq: OK
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
Starting input-event-daemon: input-event-daemon: Start parsing /etc/input-event-daemon.conf...
input-event-daemon: Adding device: /dev/input/event0...
input-event-daemon: Adding device: /dev/input/event1...
input-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Adding device: /dev/input/event3...
input-event-daemon: Start listening on 4 devices...
done
root@RK3588:/# xkbcommon: ERROR: couldn't find a Compose file for locale "C" (mapped to "C")
could not create XKB compose table for locale 'C'. Disabiling compose
[ 23.388855] dwc3 fc000000.usb: device reset
[ 23.450220] android_work: sent uevent USB_STATE=CONNECTED
[ 23.454537] android_work: sent uevent USB_STATE=CONFIGURED
xkbcommon: ERROR: couldn't find a Compose file for locale "C" (mapped to "C")
could not create XKB compose table for locale 'C'. Disabiling compose
[END] 2024/7/3 18:22:14
