VLAN实验记录---对抗遗忘

sw1的接口6应该调成混杂模式，因为pc2,4,5,6的pvid各不相同而网段相同，所以往上去路由时应该剥离标记（VLAN里面是标记而不是标签）出去，这样路由器上的物理接口用来管理不带标记的流量，而vlan2流量的往上打上vlan2标记进入vlan2的子接口。

如192.168.2.1 去访问192.168.1.1 发现目标IP和自己不在一个网段，就会去找路由器，往上去的时候经过交换机，带着vlan2的标签进入r1的子接口，发现是1.1网段，就路由给物理接口，物理接口往下发包，不会带标记。交换机收到没有标记的，会把它按pvid算，打上pvid的标记（默认vlan1）所以就会给允许vlan1的所有接口转发

access 接口不打标记

交换机1配置：

vlan batch 2 to 6

interface Ethernet0/0/1
port link-type access
port default vlan 2
#
interface Ethernet0/0/2
port hybrid pvid vlan 3
port hybrid untagged vlan 3 to 6
#
interface Ethernet0/0/3
port link-type access
port default vlan 2
#
interface Ethernet0/0/4
port hybrid pvid vlan 4
port hybrid untagged vlan 3 to 4
#
interface Ethernet0/0/5
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface Ethernet0/0/6
port hybrid tagged vlan 2
port hybrid untagged vlan 3 to 6

交换机2配置：

vlan batch 2 to 6

interface Ethernet0/0/1
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface Ethernet0/0/2
port hybrid pvid vlan 5
port hybrid untagged vlan 3 5
#
interface Ethernet0/0/3
port hybrid pvid vlan 6
port hybrid untagged vlan 3 6

路由器1配置：

[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]ip address 192.168.1.1 24

[r1]int g 0/0/0.1
[r1-GigabitEthernet0/0/0.1]ip address 192.168.2.1 24
[r1-GigabitEthernet0/0/0.1]dot1q termination vid 2
[r1-GigabitEthernet0/0/0.1]arp broadcast enable
[r1-GigabitEthernet0/0/0.1]q
[r1]ip pool v2
[r1-ip-pool-v2]network 192.168.2.0 mask 24
[r1-ip-pool-v2]gateway-list 192.168.2.1
[r1-ip-pool-v2]q
[r1]ip pool v3-v6
[r1-ip-pool-v3-v6]network 192.168.1.0 mask 24
[r1-ip-pool-v3-v6]gateway-list 192.168.1.1
[r1-ip-pool-v3-v6]q
[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]q
[r1]dhcp enable
[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]dhcp select gl
[r1-GigabitEthernet0/0/0]int g 0/0/0.1
[r1-GigabitEthernet0/0/0.1]dhcp select global
[r1-GigabitEthernet0/0/0.1]q