20240112让移远mini-PCIE接口的4G模块EC20在Firefly的AIO-3399J开发板的Android11下跑通【DTS部分】

20240112让移远mini-PCIE接口的4G模块EC20在Firefly的AIO-3399J开发板的Android11下跑通【DTS部分】
2024/1/12 16:20

https://blog.csdn.net/u010164190/article/details/79096345
[Android6.0][RK3399] PCIe 接口 4G模块 EC20 调试记录

https://blog.csdn.net/hnjztyx/article/details/72495433
S5P4418 android 5.1 EC20 R2.0 PCIE接口调试记录

步骤：
1、使用Firefly的AIO-3399【RK3399】开发板，在Android11下调通加USB底板的移远4G模块EC20。
2、将移远mini-PCIE接口的4G模块EC20接入Firefly的AIO-3399，Android11启动之后不能同构4G上网。也没有/dev/ttyUSB2这个设备节点！
3、使用AIO-3399J的DTS【Android10】替换默认的挖掘机的DTS之后，更新的内核可以让移远的EC20通过4G上网。
4、将AIO-3399J的DTS【Android10】合并/替换到挖掘机的DTS之后，更新的内核也可以让移远的EC20通过4G上网。
步骤：根据经验，将AIO-3399J的DTS文件对应到相应的挖掘机的DTS文件之中。
对于：AIO-3399J 和挖掘机都有的DTS项目，直接使用 AIO-3399J的DTS项目覆盖挖掘机的DTS项目。
对于只在 AIO-3399J 出现的项目，合并到挖掘机对应文件的最后面。
对于只在挖掘机DTS中的项目不处理！

1、
现在可以确认：问题出在DTS设备树的配置部分了！
现在开始比对AIO-3399J和挖掘机的DTS的异同。
Z:\firefly\rockchip-excavator
Makefile
rk3399-android.dtsi
rk3399-dram-default-timing.dtsi
rk3399-excavator-sapphire.dtsi
rk3399-opp.dtsi
rk3399-sapphire-excavator-edp-avb.dts
rk3399-sapphire-excavator-edp.dtsi
rk3399-sapphire.dtsi
rk3399-sched-energy.dtsi
rk3399-vop-clk-set.dtsi
rk3399.dtsi

Z:\firefly\rockchip-firefly
Makefile
rk3399-android.dtsi
rk3399-dram-default-timing.dtsi
rk3399-firefly-aio.dts
rk3399-firefly-aio.dtsi
rk3399-firefly-core.dtsi
rk3399-firefly-demo.dtsi
rk3399-firefly-port.dtsi
rk3399-opp.dtsi
rk3399-sched-energy.dtsi
rk3399-vop-clk-set.dtsi
rk3399.dtsi

干掉同名的文件，差异的文件有：
Z:\firefly\rockchip-excavator
rk3399-excavator-sapphire.dtsi
rk3399-sapphire-excavator-edp-avb.dts
rk3399-sapphire-excavator-edp.dtsi
rk3399-sapphire.dtsi

Z:\firefly\rockchip-firefly
rk3399-firefly-aio.dts
rk3399-firefly-aio.dtsi
rk3399-firefly-core.dtsi
rk3399-firefly-demo.dtsi
rk3399-firefly-port.dtsi

很容易/根据经验/很艰难地比对文件，可以知道：
rk3399-firefly-aio.dts 合并到 rk3399-sapphire-excavator-edp-avb.dts
rk3399-firefly-aio.dtsi 合并到 rk3399-sapphire-excavator-edp.dtsi
rk3399-firefly-core.dtsi 合并到 rk3399-sapphire.dtsi
rk3399-firefly-demo.dtsi 望文生义/根据名字，忽略掉，本文件不处理！
rk3399-firefly-port.dtsi 合并到 rk3399-excavator-sapphire.dtsi

放心，第一次合并/干的时候肯定会出现没有加全/遗漏的问题！
就会出现内核编译不过的问题！那就请根据经验修改吧！
rootroot@rootroot-X99-Turbo:~/3TB/76Android11.0/kernel$
rootroot@rootroot-X99-Turbo:~/3TB/76Android11.0/kernel$ make ARCH=arm64 BOOT_IMG=../rockdev/Image-rk3399_Android11/boot.img rk3399-sapphire-excavator-edp-avb.img -j36
DTC arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb
CALL scripts/checksyscalls.sh
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: ERROR (phandle_references): /amba/dma-controller@ff6d0000: Reference to non-existent node or label "iram"

arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: ERROR (phandle_references): /i2c@ff110000/gc2145@3c/port/endpoint: Reference to non-existent node or label "dvp_in_fcam"

ERROR: Input tree has errors, aborting (use -f to force output)
make[1]: *** [scripts/Makefile.lib:307: arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb] Error 2
make: *** [arch/arm64/Makefile:145: rockchip/rk3399-sapphire-excavator-edp-avb.dtb] Error 2
make: *** Waiting for unfinished jobs....
rootroot@rootroot-X99-Turbo:~/3TB/76Android11.0/kernel$ make ARCH=arm64 BOOT_IMG=../rockdev/Image-rk3399_Android11/boot.img rk3399-sapphire-excavator-edp-avb.img -j36
DTC arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb
CALL scripts/checksyscalls.sh
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: Warning (sound_dai_property): /rt5640-sound/simple-audio-card,dai-link@1/cpu:sound-dai: cell 1 is not a phandle reference
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: Warning (sound_dai_property): /rt5640-sound/simple-audio-card,dai-link@1/cpu: Missing property '#sound-dai-cells' in node /interrupt-controller@fee00000 or bad phandle (referred from sound-dai[1])
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: Warning (sound_dai_property): /rt5640-sound/simple-audio-card,dai-link@1/codec:sound-dai: cell 1 is not a phandle reference
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: Warning (sound_dai_property): /rt5640-sound/simple-audio-card,dai-link@1/codec: Missing property '#sound-dai-cells' in node /interrupt-controller@fee00000 or bad phandle (referred from sound-dai[1])
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator-edp-avb.dtb: Warning (graph_endpoint): /i2c@ff110000/xc7160b@1b/port/endpoint: graph connection to node '/syscon@ff770000/mipi-dphy-rx0/ports/port@0/endpoint@2' is not bidirectional
LDS arch/arm64/kernel/vdso/vdso.lds
CC arch/arm64/kernel/vdso/vgettimeofday.o
AS arch/arm64/kernel/vdso/note.o
AS arch/arm64/kernel/vdso/sigreturn.o
LD arch/arm64/kernel/vdso/vdso.so.dbg
VDSOSYM include/generated/vdso-offsets.h
CHK include/generated/compile.h

2、等你终于编译通过了，单独更新boot.img之后，就kernel/boot了，但是HDMI显示器黑屏，进不了Android11系统的UI界面！
[ 659.614425] init: starting service 'vendor.audio-hal'...
[ 659.618551] init: starting service 'audioserver'...
[ 659.622310] init: starting service 'surfaceflinger'...
[ 659.622924] init: Could not create socket 'pdx/system/vr/display/client': Failed to bind socket 'pdx/system/vr/display/client': No such file or directory
[ 659.623283] init: Could not create socket 'pdx/system/vr/display/manager': Failed to bind socket 'pdx/system/vr/display/manager': No such file or directory
[ 659.623583] init: Could not create socket 'pdx/system/vr/display/vsync': Failed to bind socket 'pdx/system/vr/display/vsync': No such file or directory
[ 659.627313] init: starting service 'vendor.hwcomposer-2-1'...
[ 659.631574] init: processing action (init.svc.audioserver=running) from (/system/etc/init/audioserver.rc:35)
[ 659.631955] init: Command 'start vendor.audio-hal-4-0-msd' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:37) took 0ms and failed: service vendor.audio-hal-4-0-msd not found
[ 659.632051] init: Command 'start vendor.audio-hal-2-0' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:39) took 0ms and failed: service vendor.audio-hal-2-0 not found
[ 659.717087] type=1400 audit(1358499661.996:1072): avc: denied { read } for comm="android.hardwar" name="resolution_white.xml" dev="dm-0" ino=3901 scontext=u:r:hal_graphics_composer_default:s0 tcontext=u:object_r:system_file:s0 tclass=file permissive=0
[ 661.782216] type=1400 audit(1358499664.080:1073): avc: denied { read } for comm="Binder:177_2" name="wakeup9" dev="sysfs" ino=24029 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 661.782403] type=1400 audit(1358499664.080:1074): avc: denied { read } for comm="Binder:177_2" name="wakeup7" dev="sysfs" ino=23543 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 661.783030] type=1400 audit(1358499664.080:1075): avc: denied { read } for comm="Binder:177_2" name="wakeup10" dev="sysfs" ino=24085 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 661.783678] type=1400 audit(1358499664.080:1076): avc: denied { read } for comm="Binder:177_2" name="wakeup8" dev="sysfs" ino=23583 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 661.783793] type=1400 audit(1358499664.080:1077): avc: denied { read } for comm="Binder:177_2" name="wakeup13" dev="sysfs" ino=28271 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 661.783882] type=1400 audit(1358499664.080:1078): avc: denied { read } for comm="Binder:177_2" name="wakeup6" dev="sysfs" ino=22974 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 661.783968] type=1400 audit(1358499664.080:1079): avc: denied { read } for comm="Binder:177_2" name="wakeup11" dev="sysfs" ino=24169 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 664.081178] healthd: battery l=50 v=3 t=2.6 h=2 st=3 fc=100 chg=au
[ 664.620523] init: starting service 'vendor.audio-hal'...
[ 664.624465] init: starting service 'audioserver'...
[ 664.628308] init: starting service 'surfaceflinger'...
[ 664.629009] init: Could not create socket 'pdx/system/vr/display/client': Failed to bind socket 'pdx/system/vr/display/client': No such file or directory
[ 664.629350] init: Could not create socket 'pdx/system/vr/display/manager': Failed to bind socket 'pdx/system/vr/display/manager': No such file or directory
[ 664.629657] init: Could not create socket 'pdx/system/vr/display/vsync': Failed to bind socket 'pdx/system/vr/display/vsync': No such file or directory
[ 664.633580] init: starting service 'vendor.hwcomposer-2-1'...
[ 664.637739] init: processing action (init.svc.audioserver=running) from (/system/etc/init/audioserver.rc:35)
[ 664.638007] init: Command 'start vendor.audio-hal-4-0-msd' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:37) took 0ms and failed: service vendor.audio-hal-4-0-msd not found
[ 664.638139] init: Command 'start vendor.audio-hal-2-0' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:39) took 0ms and failed: service vendor.audio-hal-2-0 not found
[ 664.719297] type=1400 audit(1358499667.006:1080): avc: denied { read } for comm="android.hardwar" name="resolution_white.xml" dev="dm-0" ino=3901 scontext=u:r:hal_graphics_composer_default:s0 tcontext=u:object_r:system_file:s0 tclass=file permissive=0
[ 665.338724] selinux: SELinux: Could not stat /sys/devices/virtual/net/ipsec_test/queues/tx-0: No such file or directory.
[ 665.338772] selinux:
[ 666.786637] type=1400 audit(1358499669.083:1081): avc: denied { read } for comm="Binder:177_2" name="wakeup9" dev="sysfs" ino=24029 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 666.786799] type=1400 audit(1358499669.083:1082): avc: denied { read } for comm="Binder:177_2" name="wakeup7" dev="sysfs" ino=23543 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 666.786985] type=1400 audit(1358499669.083:1083): avc: denied { read } for comm="Binder:177_2" name="wakeup10" dev="sysfs" ino=24085 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 666.787470] type=1400 audit(1358499669.083:1084): avc: denied { read } for comm="Binder:177_2" name="wakeup8" dev="sysfs" ino=23583 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 666.787602] type=1400 audit(1358499669.083:1085): avc: denied { read } for comm="Binder:177_2" name="wakeup13" dev="sysfs" ino=28271 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 666.787694] type=1400 audit(1358499669.083:1086): avc: denied { read } for comm="Binder:177_2" name="wakeup6" dev="sysfs" ino=22974 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 666.787784] type=1400 audit(1358499669.083:1087): avc: denied { read } for comm="Binder:177_2" name="wakeup11" dev="sysfs" ino=24169 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 669.626628] init: starting service 'vendor.audio-hal'...
[ 669.630678] init: starting service 'audioserver'...
[ 669.634637] init: starting service 'surfaceflinger'...
[ 669.635355] init: Could not create socket 'pdx/system/vr/display/client': Failed to bind socket 'pdx/system/vr/display/client': No such file or directory
[ 669.635707] init: Could not create socket 'pdx/system/vr/display/manager': Failed to bind socket 'pdx/system/vr/display/manager': No such file or directory
[ 669.636015] init: Could not create socket 'pdx/system/vr/display/vsync': Failed to bind socket 'pdx/system/vr/display/vsync': No such file or directory
[ 669.639744] init: starting service 'vendor.hwcomposer-2-1'...
[ 669.643761] init: processing action (init.svc.audioserver=running) from (/system/etc/init/audioserver.rc:35)
[ 669.643992] init: Command 'start vendor.audio-hal-4-0-msd' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:37) took 0ms and failed: service vendor.audio-hal-4-0-msd not found
[ 669.644071] init: Command 'start vendor.audio-hal-2-0' action=init.svc.audioserver=running (/system/etc/init/audioserver.rc:39) took 0ms and failed: service vendor.audio-hal-2-0 not found
[ 669.713773] type=1400 audit(1358499672.010:1088): avc: denied { read } for comm="android.hardwar" name="resolution_white.xml" dev="dm-0" ino=3901 scontext=u:r:hal_graphics_composer_default:s0 tcontext=u:object_r:system_file:s0 tclass=file permissive=0
[ 671.781897] type=1400 audit(1358499674.076:1089): avc: denied { read } for comm="Binder:177_2" name="wakeup9" dev="sysfs" ino=24029 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 671.782153] type=1400 audit(1358499674.080:1090): avc: denied { read } for comm="Binder:177_2" name="wakeup7" dev="sysfs" ino=23543 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 671.782687] type=1400 audit(1358499674.080:1091): avc: denied { read } for comm="Binder:177_2" name="wakeup10" dev="sysfs" ino=24085 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[ 671.783353] type=1400 audit(1358499674.080:1092): avc: denied { read } for comm="Binder:177_2" name="wakeup8" dev="sysfs" ino=23583 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 671.783465] type=1400 audit(1358499674.080:1093): avc: denied { read } for comm="Binder:177_2" name="wakeup13" dev="sysfs" ino=28271 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 671.783556] type=1400 audit(1358499674.080:1094): avc: denied { read } for comm="Binder:177_2" name="wakeup6" dev="sysfs" ino=22974 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 671.783643] type=1400 audit(1358499674.080:1095): avc: denied { read } for comm="Binder:177_2" name="wakeup11" dev="sysfs" ino=24169 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0

console:/ $

3、根据经验可能是某一个文件更改之后出现的问题，
很容易/根据经验/很艰难地定位文件，可以知道：
【问题出在这里，整个文件不要合并了！】
rk3399-firefly-aio.dts 合并到 rk3399-sapphire-excavator-edp-avb.dts

【合并一下的3个文件，解决编译的问题！】更新的内核也可以让移远的EC20通过4G上网。
rk3399-firefly-aio.dtsi 合并到 rk3399-sapphire-excavator-edp.dtsi
rk3399-firefly-core.dtsi 合并到 rk3399-sapphire.dtsi
rk3399-firefly-demo.dtsi 望文生义/根据名字，忽略掉，本文件不处理！
rk3399-firefly-port.dtsi 合并到 rk3399-excavator-sapphire.dtsi

4、查找PCIE/PCIE0根据经验更新代码块即可。
rk3399-firefly-port.dtsi 合并到 rk3399-excavator-sapphire.dtsi
   wireless-bluetooth {
       compatible = "bluetooth-platdata";
       clocks = <&rk808 1>;
       clock-names = "ext_clock";
       //wifi-bt-power-toggle;
       uart_rts_gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; /* GPIO2_C3 */
       pinctrl-names = "default", "rts_gpio";
       pinctrl-0 = <&uart0_rts>, <&bt_reset_gpio>, <&bt_wake_gpio>, <&bt_irq_gpio>;
       pinctrl-1 = <&uart0_gpios>;
       //BT,power_gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>; /* GPIOx_xx */
       BT,reset_gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>; /* GPIO0_B1 */
       BT,wake_gpio = <&gpio2 26 GPIO_ACTIVE_HIGH>; /* GPIO2_D2 */
       BT,wake_host_irq = <&gpio0 4 GPIO_ACTIVE_HIGH>; /* GPIO0_A4 */
       status = "okay";
   };

   vdd_pcie3v3: vdd3v3-pcie-regulator {
       compatible = "regulator-fixed";
       enable-active-high;
       gpio = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
       pinctrl-names = "default";
       pinctrl-0 = <&pcie_drv>;
       regulator-name = "vdd3v3_pcie";
   };
   vcc3v3_3g: vcc3v3-3g-regulator {
   compatible = "regulator-fixed";
   enable-active-high;
   regulator-always-on;
   regulator-boot-on;
   gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
   pinctrl-names = "default";
   pinctrl-0 = <&pcie_3g_drv>;
   regulator-name = "vcc3v3_3g";
};
};

&dfi {
status = "okay";
};

&pcie0 {
   ep-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
   num-lanes = <4>;
   pinctrl-names = "default";
   pinctrl-0 = <&pcie_clkreqn_cpm>;
};

修改为：
&pcie0 {
   ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
   num-lanes = <4>;
   pinctrl-names = "default";
   pinctrl-0 = <&pcie_clkreqn_cpm>;
   vpcie3v3-supply = <&vdd_pcie3v3>;
   status = "okay";
};

&uart0 {
   pinctrl-names = "default";
   pinctrl-0 = <&uart0_xfer &uart0_cts>;
   status = "okay";
};

&pinctrl {
   sdio-pwrseq {
       wifi_enable_h: wifi-enable-h {
           rockchip,pins =
               <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
       };
   };

   wireless-bluetooth {
       uart0_gpios: uart0-gpios {
           rockchip,pins =
               <2 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
       };
       bt_reset_gpio: bt-reset-gpio {
           rockchip,pins =
               <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
       };
       bt_wake_gpio: bt-wake-gpio {
           rockchip,pins =
               <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
       };
       bt_irq_gpio: bt-irq-gpio {
           rockchip,pins =
               <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
       };
   };

pcie {
pcie_drv: pcie-drv {
rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_none>;
};

pcie_3g_drv: pcie-3g-drv {
rockchip,pins = <2 6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};

5、虽然改动居多，但是查找PCIE/PCIE0根据经验更新代码块即可。
rk3399-firefly-aio.dtsi 合并到 rk3399-sapphire-excavator-edp.dtsi
   tc358749x: tc358749x@0f {
       compatible = "toshiba,tc358749x";
       reg = <0x0f>;
       //power-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
       power18-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>;
       power33-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
       csi-ctl-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
       stanby-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
       reset-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
       int-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
       pinctrl-names = "default";
       pinctrl-0 = <&hdmiin_gpios>;
       status = "disabled";
   };

&vopl {
   status = "okay";
   assigned-clocks = <&cru DCLK_VOP1_DIV>;
   assigned-clock-parents = <&cru PLL_VPLL>;
};

&pcie_phy {
status = "okay";
};

&pcie0 {
status = "okay";
};

修改为：
&vopl {
   status = "okay";
   assigned-clocks = <&cru DCLK_VOP1_DIV>;
   assigned-clock-parents = <&cru PLL_VPLL>;
};

&vdd_pcie3v3 {
gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>; //change with power led
};

&vcc3v3_3g {
gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
};

&pcie_phy {
status = "okay";
};

&pcie0 {
ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
status = "okay";
};

&rt5651_sound {
status = "okay";
};

&pinctrl {
   cam0 {
       cif_pwr: cif-pwr {
           rockchip,pins = <1 22 RK_FUNC_GPIO &pcfg_pull_up>;
       };
   };

pcie {
pcie_drv: pcie-drv {
rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_none>;
};

pcie_3g_drv: pcie-3g-drv {
rockchip,pins = <2 6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};

   lcd-panel {
       lcd_panel_reset: lcd-panel-reset {
           rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
       };
   };

   hdmiin {
       hdmiin_gpios: hdmiin_gpios {
       rockchip,pins =
               <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>,
               <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
               <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
               <2 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
               <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>,
               <2 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
       };
   };
};

6、最后很容易/根据经验/很艰难地定位文件，可以知道是这里的问题【电源的配置】：
rk3399-firefly-core.dtsi 合并到 rk3399-sapphire.dtsi
Z:\3TB\76Android11.0\kernel\arch\arm64\boot\dts\rockchip\rk3399-sapphire.dtsi
&i2s2 {
status = "okay";
};

&io_domains {
status = "okay";

   bt656-supply = <&vcc_3v0>;
   audio-supply = <&vcca1v8_codec>;
   sdmmc-supply = <&vcc_sdio>;
   gpio1830-supply = <&vcc_3v0>;
};

&pmu_io_domains {
pmu1830-supply = <&vcc_3v0>;
status = "okay";
};

修改为：
&i2s2 {
status = "okay";
};

&io_domains {
status = "okay";

   bt656-supply = <&vcc1v8_dvp>;       /* bt656_gpio2ab_ms */
   audio-supply = <&vcca1v8_codec>;   /* audio_gpio3d4a_ms */
   //sdmmc-supply = <&vcc_sd>;       /* sdmmc_gpio4b_ms */
   sdmmc-supply = <&vcc_sdio>;
   gpio1830-supply = <&vcc_3v0>;       /* gpio1833_gpio4cd_ms */
};

&pmu_io_domains {
pmu1830-supply = <&vcc_3v0>;
status = "okay";
};

7、使用USB底板的EC20能够上网需要修改的部分：
缘起：使用友善之臂的Android11可以让EC20上网，但是同样的修改步骤，Toybrick的Android11不能让EC20上网。
最后确认是selinux的问题！

开发板：Firefly的AIO-3399J【RK3399】
SDK：rk3399-android-11-r20211216.tar.xz【Android11】
Android11.0.tar.bz2.aa【ToyBrick】
Android11.0.tar.bz2.ab
Android11.0.tar.bz2.ac

https://wiki.t-firefly.com/AIO-3399J/prepare_compile_android.html
AIO-3399J产品规格书立即购买
AIO-3399J 采用 RK3399 六核(A72x2+A53x4) 64 位处理器，主频高达1.8GHz，集成了四核 Mali-T860 GPU，性能优异。

0、简略步骤：
rootroot@rootroot-X99-Turbo:~/3TB$ cat Android11.0.tar.bz2.a* > Android11.0.tar.bz2
rootroot@rootroot-X99-Turbo:~/3TB$ tar jxvf Android11.0.tar.bz2
rootroot@rootroot-X99-Turbo:~/3TB$ mv Android11.0 64rk3399-android-11
rootroot@rootroot-X99-Turbo:~/3TB$ cd 64rk3399-android-11
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ cd u-boot
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11/u-boot$ ./make.sh rk3399
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11/u-boot$ cd ..
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ cd kernel/
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11/kernel$ make ARCH=arm64 rockchip_defconfig android-11.config -j36
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11/kernel$ make ARCH=arm64 BOOT_IMG=../rockdev/Image-rk3399_Android11/boot.img rk3399-sapphire-excavator-edp-avb.img -j36
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ source build/envsetup.sh
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ lunch
36. rk3399_Android11-userdebug
Which would you like? [aosp_arm-eng] 36
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ make -j36
rootroot@rootroot-X99-Turbo:~/3TB/64rk3399-android-11$ ./build.sh -u

1、
Android11 + Kernel所需要修改的文件：
1、【完全一致/相同】
Z:\rk3399-android-11\device\rockchip\common\4g_modem\manifest.xml

2、复制库文件：
chat
dhcpcd
ip-down
ip-up
libmeig-ril.so
libquec-ril.so
libreference-ril-62.so
libreference-ril.so

Z:\rk3399-android-11\device\rockchip\common\ec20\chat
Z:\rk3399-android-11\device\rockchip\common\ec20\dhcpcd
Z:\rk3399-android-11\device\rockchip\common\ec20\ip-down
Z:\rk3399-android-11\device\rockchip\common\ec20\ip-up
Z:\rk3399-android-11\device\rockchip\common\ec20\libmeig-ril.so
Z:\rk3399-android-11\device\rockchip\common\ec20\libquec-ril.so
Z:\rk3399-android-11\device\rockchip\common\ec20\libreference-ril-62.so
Z:\rk3399-android-11\device\rockchip\common\ec20\libreference-ril.so

3、
Z:\rk3399-android-11\device\rockchip\common\BoardConfig.mk

4、
Z:\rk3399-android-11\device\rockchip\common\device.mk

5、
Z:\rk3399-android-11\device\rockchip\common\ueventd.rockchip.rc

6、
Z:\rk3399-android-11\device\rockchip\rk3399\rk3399_Android11\overlay\frameworks\base\core\res\res\values\config.xml

【不用修改】
Z:\rk3399-android-11\device\rockchip\rk3399\device.mk

7、
Z:\rk3399-android-11\kernel\drivers\net\usb\Makefile
Z:\rk3399-android-11\kernel\drivers\net\usb\qmi_wwan_q.c

8、
Z:\rk3399-android-11\kernel\drivers\usb\serial\option.c
【几乎没有改动】
Z:\rk3399-android-11\kernel\drivers\usb\serial\qcserial.c
Z:\rk3399-android-11\kernel\drivers\usb\serial\usb_wwan.c

9、
Z:\rk3399-android-11\system\core\init\devices.cpp

3、修改selinux部分：
https://blog.csdn.net/taye_year/article/details/125948529
https://codeleading.com/article/76926405628/
RK3568移远4G模块EC20

Z:\3TB\76Android11.0\device\rockchip\common\ueventd.rockchip.rc
Z:\3TB\76Android11.0\device\rockchip\common\sepolicy\private\file_contexts
Z:\3TB\76Android11.0\system\sepolicy\vendor\rild.rc

【相关的资料：】
百度搜索：ifeq ($(strip $(BOARD_HAS_EC20_MODEM)),true)

RK3399 EC20 步骤
Android6.0 RK3399 PCIe 接口 4G模块 EC20 调试记录
rk3568 Android11系统调试ec20模块的gps功能
RK3568-ANDROID11-4G-EC20-(详细步骤)
RK356X android11 移远EC20 modem支持

[ 87.794373] init: Sending signal 9 to service 'ril-daemon' (pid 2176) proce
重复打印'android.hardware.radio@1.1::IRadio/slot1'
+ if(strcmp(descriptor.c_str(),"android.hardware.radio@1.1::IRadio") != 0)
[ 44.972959] init: Control message: Processed ctl.interface_start for 'andro

'android.hardware.radio@1.1::IRadio/slot1' from pid: 154 (/system/bin/hwserv
init: Control message: Processed ctl.interface_start for 'android.hardware.r
type=1400 audit(1704645252.746:494): avc: denied { read write } for comm="ri

BING：[ 44.972959] init: Control message: Processed ctl.interface_start for 'android.hardware.radio@1.1::IRadio/slot1' from pid: 149 (/system/bin/hwservicemanager)

https://blog.csdn.net/longmin96/article/details/122716504
RK3568-ANDROID11-4G-EC20-(详细步骤)
注意：硬件可以先使用USB转接板把模块接到电脑上，使用AT指令把模块调好。

https://blog.csdn.net/longmin96/article/details/122687117
RK3568-ANDROID11-4G-EC20-驱动篇（移远模块）
旋风旋风

https://blog.csdn.net/longmin96/article/details/122687865
RK3568-ANDROID11-4G-EC20-系统篇（移远模块）
首先，要先获得技术支持
步骤一，先在USB模块上完成4G
步骤二，移植到PCIE座子上

https://blog.csdn.net/weixin_51178981/article/details/124804679
NXP(imx8qxp)上android11的EG25-G(4G)模块调试记录

修改selinux的权限
修改/system/core/init/selinux.cpp
diff --git a/init/selinux.cpp b/init/selinux.cpp
index 5a0255acd..ae6f1fce9 100644
--- a/init/selinux.cpp
+++ b/init/selinux.cpp
@@ -104,6 +104,7 @@ EnforcingStatus StatusFromCmdline() {
}

bool IsEnforcing() {
+ return false;
if (ALLOW_PERMISSIVE_SELINUX) {
return StatusFromCmdline() == SELINUX_ENFORCING;
}

https://blog.csdn.net/terry_xiwang/article/details/123137864
RK3568 Android12 移远4G模块EM05-CE 调试心得

4、适配Android部分的时候主要是利用了rk已有的4g modem框架，打开BOARD_HAS_RK_4G_MODEM属性，并将librk-ril.so 替换为Quectel的ril库，这样会少走一些弯路。
5、我用的ril库版本为Quectel_Android_RIL_Driver_V3.3.78，这个版本才能适配Android12。之前用过3.3.57和3.3.62版本的库，加载时都会报错：

【关闭多余的打印LOG】
https://bbs.elecfans.com/jishu_2263076_1_1.html
[问答] 如何调试RK3568-ANDROID11-4G-EC20？

【下载】
https://download.csdn.net/download/seasonfangjing/86247556?utm_source=bbsseo
RK356X android11 移远EC20 modem支持

https://blog.csdn.net/weixin_38420901/article/details/129875533
移远EC20 WINDOWS下安装驱动及开机自动拨号上网
https://download.csdn.net/download/weixin_38420901/87635376
移远EC20 Windows驱动
https://download.csdn.net/download/guoruibin123/19886298
移远EC20 R2.0 全网通4G模块软硬件设计技术资料包（包括模块封装+软硬件设计文档+软件驱动）.zip
https://download.csdn.net/download/xieyunfei1999/88332693
移远USB驱动V2.2.2 Quectel-LTE&5G-Windows-USB-Driver-V2.2.2 EC20最新驱动

https://blog.csdn.net/yjz_0314/article/details/134142847
Android11.0系统中适配EC20模块4G及GPS功能
https://download.csdn.net/download/yjz_0314/88490693?spm=1001.2101.3001.9500
Android11.0系统中适配EC20模块4G及GPS功能

https://download.csdn.net/download/seasonfangjing/88073682
RK3588S android13 ec20 modem移植

https://blog.csdn.net/xierong1/article/details/127091908
rk3399调试EC20 4G模块

还有 android 8.1 与5.1区别很大就是系统权限
Selinux
./device/rockchip/common/sepolicy/rild.te
./system/sepolicy/vendor/rild.te
./system/sepolicy/public/rild.te
./system/sepolicy/prebuilts/api/26.0/public/rild.te

https://www.cnblogs.com/lialong1st/p/11266330.html
https://blog.csdn.net/weixin_30273931/article/details/101681600
RK3399 4G模块移远EC20移植调试

https://download.csdn.net/download/weixin_44498318/18300885
RK3399 安卓Q适配EC20 4G模块资料

https://blog.csdn.net/linux_qian/article/details/90715599/
rk3399添加EC25E/EC20...模组

搞来搞去搞了很久，差点放弃走人的时候，发现竟然是这点事。。。辛酸史如下：
android6.01-----kernel4.4.36-----编译环境ubuntu16.04
一、kernel driver
内核有4种驱动方式，usb serial、CDC ACM、Gobinet、QMI WWAN，本文选用的是usb serial和QMI WWAN两种驱动。

（4）打开dongle功能
/device/rockchip/common/BoardConfig.mk
BOARD_HAVE_DONGLE ?= true

（5）检查
logcat -b radio -v time //查看log
getprop init.svc.ril-daemon //检查ril守护进程Runing
cat init.rc | grep ril-daemon //检查ril-daemon服务是否生效
getenforce //检查SELinux是否开启，<setenforce 0>命令关闭
getprop gsm.version.ril-impl //检查ril版本，出现Quectel_Android_RIL_SR01A41V17,如未出现ril库没有添加上，或者检查phone进程

https://blog.csdn.net/weixin_43069863/article/details/126587254
rk3568 4g 模块调试-ec20（移远模块）

如果无法上网，也可以尝试修改上网状态的选择模式

--- a/frameworks/base/telephony/java/com/android/internal/telephony/RILConstants.java
+++ b/frameworks/base/telephony/java/com/android/internal/telephony/RILConstants.java
@@ -237,7 +237,7 @@ public interface RILConstants {
int PREFERRED_NETWORK_MODE = Optional.of(TelephonyProperties.default_network())
.filter(list -> !list.isEmpty())
.map(list -> list.get(0))
- .orElse(NETWORK_MODE_WCDMA_PREF);
+ .orElse(NETWORK_MODE_LTE_GSM_WCDMA);

int BAND_MODE_UNSPECIFIED = 0; //"unspecified" (selected by baseband automatically)
int BAND_MODE_EURO = 1; //"EURO band" (GSM-900 / DCS-1800 / WCDMA-IMT-2000)

https://blog.csdn.net/weixin_44498318/article/details/109289482
Android：记录一下RK3399 安卓Q适配EC20 4G模块（附log）

4.2 SELinux权限问题
添加权限：
SELinux权限问题解决方法 - CSDN
Selinux SeAndroid理解 - CSDN
Android : SELinux 简析&修改 - 博客园
默认关闭/开启权限：
ANDROID10 关闭SELINUX权限方法 - 灰信网

参考资料：
http://www.friendlyelec.com.cn/agent.asp
http://www.friendlyelec.com.cn/
https://download.friendlyelec.com/NanoPC-T4
https://wiki.friendlyelec.com/wiki/index.php/NanoPC-T4/zh#.E4.B8.8B.E8.BD.BDAndroid10.E6.BA.90.E4.BB.A3.E7.A0.81

https://item.taobao.com/item.htm?spm=a1z09.2.0.0.37562e8dcotDm6&id=570312633249&_u=7ju3ku004a
友善NanoPC-T4瑞芯微RK3399开发板ROS双摄4K播放开源AI智能安卓10

WiKi维基教程（固件介绍，使用说明，操作步骤等）
http://wiki.friendlyelec.com/wiki/index.php/NanoPC-T4
系统固件下载
https://dl.friendlyelec.com/nanopct4
原理图(pdf格式)
http://wiki.friendlyelec.com/wiki/images/e/e0/NanoPC-T4-1902-Schematic.pdf
尺寸图(dxf格式)
http://wiki.friendlyelec.com/wiki/images/b/bc/NanoPC-T4_1802_Drawing%28dxf%29.zip

http://www.friendlyelec.com.cn/nanopi-m4.asp
NanoPi M4 | NanoPi M4V2

https://wiki.friendlyelec.com/wiki/index.php/NanoPi_M4/zh
15.3 编译Android10源代码
15.3.1 下载Android10源代码
有以下两种途径获取 Android10 的源代码，都需要联网:

使用网盘里的git repo压缩包
网盘下载地址: 点击进入

https://download.friendlyelec.com/NanoPiM4
https://pan.baidu.com/share/init?surl=oBLn9H31hILJKEPQXgrUog
提取码：yn6r